- Home
- Applications
- burner
Refine by
Industries served
- Energy
- Air and Climate
- Oil, Gas & Refineries
- Manufacturing, Other
- Agriculture
- Construction & Construction Materials
- Automobile & Ground Transport
- Metal
- Pulp & Paper
- Monitoring and Testing
- Aerospace & Air Transport
- Chemical & Pharmaceuticals
- Electronics and Computers
- Glassware
- Communications / Telecom / Datacom
- Environmental
- Soil and Groundwater
Burner Product Applications
78 applications found
Fume hoods and hazardous material storage areas are very susceptible to fires. Protect them today. Laboratories present a significant risk of fire. Detecting a fire in its early stage is critically important for reducing the risk of injury to laboratory personnel and the damage to equipment. Our suppression systems can detect and suppress a small fire before it grows and requires extinguishment by the building’s sprinkler ...
ByFiretrace International LLC based in Scottsdale, ARIZONA (USA)
Manufacturing of automobiles and auto components involves many steps such as casting, forging, painting and electroplating etc that require heat or steam. Original Equipment Manufacturers and larger players have in-house facilities to perform the above mentioned activities. However, some industries outsource the activities ie: electroplating and painting of the auto components to smaller and unorganized sector/units. The entire process requires large amount of energy in the form of both heat and electrical energy. ...
ByClique Solar based in Mumbai, INDIA
The advantages of the TORBED technologies for production of energy from biomass are: Faster and more precise temperature control - important with high alkali feed stocks to prevent accretions. Handling of irregularly shaped solid feed stocks – this minimizes feed stock shredding, chipping or milling. Low pressure drop allowing process gas recirculation for maximum turndown - 50:1 achievable. Rapid start-up and program change. Smaller size with easy installation. Simplicity in operation and ease of automation ...
ByTorftech Group based in Thatcham, UNITED KINGDOM
In Fluid Catalytic Cracking (FCC) processes, widely used in oil refineries, the separation and recovery of powder catalysts is a major concern. Particularly, the concentration of catalyst after the FCC regenerator is usually over 150 mg/Nm3. Since these levels of emissions didn't represent any environmental harm in the past, they were not controlled by any separator or filter. Plant managers main concern was to clean a fraction of the gas to produce energy in a Turbo Expander, or similar, while concentrating the ...
ByAdvanced Cyclone Systems, S. A. (ACS) based in Porto, PORTUGAL
Substituting pyrolysis oil for fossil fuel can be already be done today by medium or large-scale (co-)combustion of natural gas, coal or heating oil fired boilers, furnaces and turbines. Retrofitting these systems requires limited investments and due to its GHG savings of around 90% pyrolysis oil offers a unique opportunity to make your energy supply more sustainable while also reducing your dependency on fossil fuel prices. Even more interesting is its use in decentralized CHP solutions found for instance in ...
ByBTG BioLiquids - BTG Biomass Technology Group based in Enschede, NETHERLANDS
Comprehensive development and test facilities for a range of thermal power and heat transfer systems are available at Energy Technology ...
ByEnergy Technology Centre Ltd based in East Kilbride, UNITED KINGDOM
Regarded by many as providing the backbone to modern society, the steel industry is one which continues to evolve. Whether it is geographic shifts in demand or production, or challenges brought by energy or raw material costs, companies continue to develop their processes and facilities to meet them. Alongside these changes companies have also realised the requirement to minimise downtime due to unplanned maintenance and protect workers from exposure to toxic or flammable gas ...
ByCrowcon Detection Instruments Ltd based in Milton Park, UNITED KINGDOM
Calcination is a process that involves heating a substance, typically a solid material, at high temperature with limited supply of air or oxygen. The purpose of calcination is to remove volatile components and drive off impurities or to transform the material into a more desirable form for further ...
ByAdvanced Cyclone Systems, S. A. (ACS) based in Porto, PORTUGAL
Control Asphalt Odors Naturally: The production of hot mix paving asphalt generates odors that can be strong, persistent, and a nuisance to employees and neighbors alike. Controlling and abating these odors can be a ...
ByEcosorb by OMI Industries based in Palatine, ILLINOIS (USA)
Biomass Power Plants generates power from biomass fuels such as wood pellets, bagasse and hog fuel. This fuels are susceptible to spontaneous combustion since it can occur at any stage of storage, production or transport. Early detection of fire or combustion is important for safety ...
ByVisionTIR based in Malaga, SPAIN
York Metal Products is an established and proven North America manufacturer of HVAC products. With the increased demand for greater efficiency and quieter operation, the importance of the design of components has also become more and more critical. We produce custom HVAC components in a wide range of sizes and shapes using both metal spinning and tube rolling to optimize product performance. ...
ByYork Metal Products based in Concord, ONTARIO (CANADA)
Co-firing is the (partial) substitution of fossil coal by biomass in coal-fired power plants. Torrefied biomass offers the most cost-effective route to significantly increase the use of biomass as a renewable energy source and to reduce the CO2 footprint of industrial coal ...
ByBlackwood Technology B.V based in Hoofddorp, NETHERLANDS
Example: Scrap copper recycling, cobalt for battery production. Similar tasks: Metal recycling, roast processes, thermal waste ...
ByCTP Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control GmbH based in Graz, AUSTRIA
The Kurz Insertion Mass Flow Meter products provide extremely reliable and accurate measurements for the harsh environment of a recovery boiler facility, without restricting airflow even in short run ...
ByKurz Instruments, Inc. based in Monterey, CALIFORNIA (USA)
High-quality natural gas fuel measurement increases efficiency in applications as well as industry plants. LEOMI thermal mass flow meters demonstrate high accuracy, low-pressure drop, and direct mass flow readings to measure natural ...
ByLeomi Instruments Pvt. Ltd based in Gandhinagar, INDIA
The entire chemical, petrochemical and pharmaceutical industry produces huge amounts of liquid residues that can be thermally recycled. In response to the principle of zero waste emission, these are increasingly being converted into thermal energy directly where they are produced. This is usually done in adiabatic combustion chamber systems with subsequent waste heat utilisation. Industrial parks also have special hazardous waste incineration plants, operated by globally active waste management companies, in which ...
ByCS Combustion Solutions GmbH based in Wien, AUSTRIA
Claus plants are used to convert H2S from natural gas and crude oil into liquid sulphur. For this purpose, the H2S-containing waste gas (Claus gas) is burnt sub-stoichiometrically in several stages, depending on the ...
ByCS Combustion Solutions GmbH based in Wien, AUSTRIA
The engineering team at Willexa Energy has been providing quality gas treatment solutions to the biogas industry for more than 20 years. With a focus on protecting engines, turbines, cataysts, micro-turbines, fuel cells, or boilers from the contaminants found in landfill and digester gas, our equipment can be found on biogas to energy projects across the country. Our filtration, chilling & dehydration, and VOC & siloxane reduction solutions will not only decrease your operating costs, they will increase ...
ByWillexa Energy, LLC based in Indian Trail, NORTH CAROLINA (USA)