- Home
- Applications
- demisting
Refine by
Demisting Product Applications
19 applications found
Process Information: In Pulp & Paper plants there are various applications for chevron vane, BlueFil® structured Mesh Demister or Knitted Wire Demister droplet separators to prevent liquid carry over from an evaporator or scrubber tower, or to recover chemicals used in the pulping process – e.g. ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
The Contec oil mist separator, type 9.200/762, with upstream demister and M6 filter cartridge ensures the reduction of particle contamination. ...
ByContec GmbH based in Bad Honnef, GERMANY
Due to the high viscosity liquid produced with over sulphonisation, it is recommended (a) to have a stand-by filter unit in parallel, or (b) to have an irrigated demister unit in front of the fibre filters; in any case a Δp metered wash spray system is normal on the candle filters, and the vessel may be trace heated and ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Global supplier and manufacturer of Separation Technologies, Process equipment, Mass Transfer and Filtration ...
ByEuromesh BV based in Sliedrecht, NETHERLANDS
PROCESS INFORMATION: The Vacuum Unit is fed with Crude Bottoms and is injected with steam. Passing upwards through wash oil stages, the gas exits to an overhead condenser, where cleaned gas goes to LT Ends, and Naphtha and Light Cycle Oil are produced as liquids. From side streams the Vacuum Unit sends HVGO to the FCC Fractionator and LVGO to the Hydrocracker or for ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
PROCESS INFORMATION: The Fractionator is fed from the reactor and side strippers are injected with steam. Naphtha and Light Cycle Oil are produced. In a Pipestill, fed from a crude furnace, the side strippers produce Jet A, Gas Oil and Diesel or Heavy Gas ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Phosphor Bronze Processing – Phosphoric Acid / P2O5 Filtration Systems. Process Information: Phosphorous is injected into a bath of molten copper, to produce Phosphor Copper metal. There is then a fume produced from the reaction in the bath, which is extracted by a fan to a filter system, before the cleaned air is then emitted to atmosphere. P2O5 mists are entrained with the fume, and frequently carbon solids are entrained also. (The origin & nature of the Phosphorous is a major factor in the quantity of ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Air or SO2 is dried with H2SO4 before being fed to the sulphur burner or converter. The Drying Tower can be under pressure or under suction, with the main gas blower being, respectively, in front of or after the tower. The physical limit of drying is 3 mg/SCF of gas as H2O (= 16 mg/SCF as H2SO4) Large particles (>3 microns) are mechanically entrained from the acid distribution system or packing, typically as a load of 500 – 750 mg/m3. As the Drying Tower operates at relatively low temperature, mist is ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Example: Production of bio-ethanol. Similar tasks: Dryers, Fibre board ...
ByCTP Chemisch Thermische Prozesstechnik GmbH / CTP Air Pollution Control GmbH based in Graz, AUSTRIA
Process Information: Candle Filters can be used in the dry process (electric furnace) described below; the phosphate rock is sintered or nodulized to facilitate escape of phosphorus vapours in the furnace and to prevent the blowing over of dust. After sintering, the material is sized and the fines returned to the sintering machine. Coke and sand are added and the materials charged to the electric furnace. The temperature of the furnace is approximately 2400 ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
PROCESS INFORMATION: The Amine gas treating, also known as gas sweetening, refers to a process that uses aqueous solutions of various alkylamines (commonly known as amines) to remove hydrogen sulphide (H2S) and carbon dioxide (CO2) from gases. Aqueous solutions of MEA (monoethanolamine) are used as a gas stream scrubbing liquid in amine treaters to remove H2S from sour natural gas. The MEA reacts with acidic compounds dissolved in the solution, using a large surface area to contact with the cold scrubbing solution ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Process Information: Case A Conventional H2SO4 Process: In a sulphur burning or metallurgical double absorption H2SO4 plant where no Oleum is produced upstream, SO3 gas exits the third catalyst pass, is cooled down and enters the first ( = intermediate ) absorption tower, where H2SO4 is distributed over ceramic packing to absorb the SO3. When the gas exits the I.A.T. it returns to the converter to go into the fourth catalyst pass after being reheated in a gas/gas heat exchanger. Due to the high inlet gas ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
PROCESS INFORMATION: The Naptha Hydrotreater prepares feedstock for downstream reforming or isomerization. The naphtha feed is mixed with hydrogen rich recycle gas. The mixed feed is then heated and then fed to the reactor, which contains a cobalt-molybdenum or nickel-molybdenum catalyst to convert contaminants such as sulphur, nitrogen, oxygenates and halides to hydrogen sulphide, ammonia, water and hydrogen halides. These can then be removed from the hydrocarbon stream. ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Fuel Gas Streams are frequently contaminated with liquid aerosols. The liquid exists as a stable and persistent “smoke” in the gas stream. The liquid contaminant can enter the gas stream through any one of a variety of events including – phase separation and condensation, compressor lube-oils from compression, chemical addition to pipelines (including corrosion inhibitors), and entrainment from overheads of contact ...
ByPentair Filtration Solutions, LLC based in Conroe, TEXAS (USA)
Process Information: Concentrated Urea solution comes from the Evaporator and is sprayed downwards from the top of the Prilling Tower. The inlet air draft rising inside the Prilling Tower cools the falling, sprayed solution, which then forms into solid ‘prills’. The prills then continue to fall, to the bottom of the tower for collection. At the top of the tower, around the sprayer heads, the Urea microprills (100 microns ) and average 1 micron diameter mist are entrained by the air going on up to the ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Most common manufacturing applications are Synthetic Leather ( car upholstery, bags, shoes etc.), vinyl coated and linoleum flooring, vinyl coated wallpaper, laminated sheets ( special films, belts, tarpaulins ) and foam products. Polyvinyl-chloride (PVC) is a thermoplastic and is mixed to additives which improve its properties and enable it to be processed more ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Process Information: Concentrated Ammonium Nitrate (NH4NO3) solution comes from the Evaporator and is sprayed downwards from the top of the Prilling Tower. The inlet air draft rising inside the Prilling Tower cools the falling, sprayed solution, which then forms into solid ‘prills’. The prills then continue to fall, to the bottom of the tower for collection. At the top of the tower, around the sprayer heads, the NH4NO3 decomposes into NH3 and HNO3 , which recombines quickly into NH4NO3 mist and is ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM
Within the nuclear industry there are ongoing operational challenges and potential hazards associated with environmental emissions and the protection of the workforce, such as high temperatures, high radioactivity, high solids loads and chemically aggressive environments. Therefore the industry demands exceptional levels of technical expertise and quality, in conjunction with specific skills to solve many of its most intractable ...
ByPorvair - Filtration Group based in Fareham, UNITED KINGDOM
Process information: Depending on the process technology and the source of the emission, the nature of the emissions (content quantity and type of contaminant) determines the best design of scrubber in each case. HF, H2FiS6 (FSA), P2O5 and NH3 are the main contaminants to be scrubbed in the exit ...
ByBegg Cousland Envirotec Limited based in Glasgow, UNITED KINGDOM