- Home
- Applications
- africa
- cems system
Refine by
Cems System Product Applications In Africa
13 applications found
Premium
OPSIS is a world-leading supplier of CEMS (continuous emissions monitoring systems) for various special applications in the industrial emissions sector. The OPSIS gas monitoring systems have been tested and approved by a range of international authorities, and has proven to have the best performance and longest calibration intervals. We specialise in the design and supply of high accuracy, low maintenance, cross-duct, non-extractive CEM ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Synspec GCs can also be used as continuous emission monitoring systems (CEMS). In general, emissions from stacks are in the higher ranges of concentrations to be measured. ...
BySynspec BV based in Groningen, NETHERLANDS
Continuous Emissions Monitoring Systems (CEMS) are used to measure flue gases from stationary sources at a wide variety of regulated industrial facilities, including power plants, petroleum refineries, petrochemical plants, waste incinerators, pulp and paper producers, and many others. ...
ByTeledyne API based in San Diego, CALIFORNIA (USA)
Premium
With decades of industrial experience, our systems are designed and developed as a complete turnkey solution. From sample extraction, through analysis, data acquisition and report management, each system is configured to comply with the normative demands and technical constraints of our clients, specific to their ...
ByENVEA based in Poissy, FRANCE
At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. A single system can be used to measure the high levels of nitrogen monoxide NO and nitrogen dioxide NO2, as well as water vapor H2O, nitrous oxide N2O, carbon monoxide CO, carbon dioxide CO2 and ammonia NH3. The fixed installation products for these purposes are the Gasmet™ CEM II measurement ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
BS EN 14181 is a quality assurance standard relevant to plants operating under the Large Combustion Plant (LCPD) and Waste Incineration (WID) Directives. Quality Assurance Level 2 (QAL2) of this standard involves the parallel testing of the plant automated measurement systems (AMS) against a certified test house, making measurements with a comparative standard. ...
ByProtea Limited based in Middlewich, UNITED KINGDOM
Protea is the most experienced company in the UK in using FTIR gas analyser to measure emissions. Through running a UKAS-accredited test house and being a manufacturer of gas analysers, we have been involved in FTIR as a supplier and end-user for 10 years. ...
ByProtea Limited based in Middlewich, UNITED KINGDOM
Modern production method of nitric acid production may lead to generation of several different gaseous emission components, such as nitrogen oxides (NOx), ammonia NH3 and nitrous oxide N2O. Nitrogen monoxide is an intermediate gaseous product in manufacturing of nitric acid HNO3. NO is formed in a catalytic reaction between ammonia and molecular oxygen O2. But undesirable side reactions may result in formation of nitrogen dioxide NO2 and nitrous oxide N2O. The NO and NO2 emissions can be reduced by use of ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Reciprocating internal combustion engines burning natural gas are a source of formaldehyde emissions. There are strict tolerances imposed on operators of engines to ensure that formaldehyde is removed effectively and that formaldehyde emissions are below published limits. The only instrumental method for formaldehyde monitoring is FTIR, following procedures such as US EPA Method 320 and Environment Agency TGN M22. Protea’s FTIR gas analysers have been specifically designed to follow these methods and our ...
ByProtea Limited based in Middlewich, UNITED KINGDOM
Current Total VOC Measurements The most common, and current standard, method for measuring Total Volatile Organic Compounds (VOC) is the use of a Flamed Ionisation Detector (FID). This gives a representative value of the total carbon content of a gas stream, as the FID cannot tell which specific organic compounds are ...
ByProtea Limited based in Middlewich, UNITED KINGDOM
Cement is the main ingredient of concrete, which is the most common building material in the world. Cement industry is one of the biggest CO2 emission producers mainly due to the huge production capacities and calcination process, which is an important part of cement production. Cement manufacturers need to monitor these emissions continuously according to local emission regulations. Read about our solutions to the cement ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Power plants are industrial facilities used to generate electric power with the help of one or more generators which convert different energy sources into electric power. Power plants need to monitor emissions continuously according to local emission regulations. Read about our solutions for the power ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Nitric acid is manufactured from ammonia and is a key chemical in the manufacture of fertilizers. This is the main reason why nitric acid is produced in such large quantities. The production process of nitric acid produces nitrogen oxides (NOx), ammonia (NH3) and nitrous oxide N2O ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND