- Home
- Applications
- canada
- conductivity resistivity
Refine by
Conductivity Resistivity Product Applications In Canada
10 applications found
Premium
Accurate fountain (dampening) solution concentration control is essential for consistent, high-quality results in lithography. Low concentration can cause drying on the non-image area of the plate resulting in tinting, scumming, blanket piling, etc. High concentrations, on the other hand, bring about over-emulsification of the ink. This results in weakening of color strength and changes in ink rheology (body and flow properties). Correct concentration will allow the non-image areas of the plate to be appropriately ...
ByMyron L Company based in Carlsbad, CALIFORNIA (USA)
Premium
Contamination of circuit boards can bring about severe degradation of insulation resistance and dielectric strength. Cleanliness of completed circuit boards is, therefore, of vital interest. For those companies who have established circuit board cleaning procedures, the MIL Spec P-a has been used as a guideline for control. Now a simple “on line” test for the relative measurement of ionic contamination has been ...
ByMyron L Company based in Carlsbad, CALIFORNIA (USA)
THORNTON specializes in measurements for pure and ultrapure water treatment with parameters of resistivity, conductivity, total organic carbon (TOC), flow, pH, ORP, dissolved oxygen and ozone. ...
ByMettler - Toledo Int. Inc based in Greifensee, SWITZERLAND
Premium
Years ago, high purity water was used only in limited applications. Today, deionized (Dl) water has become an essential ingredient in hundreds of applications including: medical, laboratory, pharmaceutical, cosmetics, electronics manufacturing, food processing, plating, countless industrial processes, and even the final rinse at the local car ...
ByMyron L Company based in Carlsbad, CALIFORNIA (USA)
Premium
The textile manufacturing industry encompasses many and diverse processes that rely heavily on the use of water, energy, chemicals, and other resources. Wet spinning, sizing, desizing, scouring, bleaching, mercerization, dyeing and printing are just a few. Monitoring and controlling the pH, TDS/Conductivity/Salt Concentration, ORP (REDOX), and Temperature of the aqueous solutions used in these processes conserves costly resources, controls quality, and reduces the amount of pollution that must be treated before ...
ByMyron L Company based in Carlsbad, CALIFORNIA (USA)
Premium
Boilers and cooling towers share two major water related problems: deposits and corrosion. As steam is generated by a boiler or water evaporating from a cooling tower, dissolved minerals are left behind, increasing the concentration of these minerals. Additional minerals are introduced via the water added to makeup the water lost to steam/evaporation. Eventually, the minerals reach a level (or cycle) of concentration that will cause either loss of efficiency due to scale or damage from corrosion. This level can be ...
ByMyron L Company based in Carlsbad, CALIFORNIA (USA)
Premium
Anyone and everyone who is responsible for operating and maintaining a swimming pool or spa has to test, monitor, and control complex, interdependent chemical factors that affect the quality of water bathers are immersed in. Additionally, aquatic facility operators must be familiar with all laws, regulations, and guidelines governing what these parameters should ...
ByMyron L Company based in Carlsbad, CALIFORNIA (USA)
Premium
Osmosis is the phenomenon of water molecules passing through a semi-permeable membrane from a region with lower dissolved solids to a region with higher dissolved solids until a near equilibrium is reached. Reverse Osmosis (RO) is a membrane process of purification which removes most of the total dissolved solids (TDS) in water by reversing the natural process of osmosis. Pressure is applied to a TDS-concentrated solution against a semi-permeable membrane, causing pure water to diffuse through the membrane. RO has ...
ByMyron L Company based in Carlsbad, CALIFORNIA (USA)
Premium
Oxidation Reduction Potential or Redox is the activity or strength of oxidizers and reducers in relation to their concentration. Oxidizers accept electrons, reducers lose electrons. Examples of oxidizers are: chlorine, hydrogen peroxide, bromine, ozone, and chlorine dioxide. Examples of reducers are sodium sulfite, sodium bisulfate and hydrogen sulfide. Like acidity and alkalinity, the increase of one is at the expense of the ...
ByMyron L Company based in Carlsbad, CALIFORNIA (USA)
In steel plants, equipment that processes sinter at very high temperature is exposed to severe wear conditions. In particular, the sinter crusher that has to ensure large through-put must be wear-protected in order to avoid expensive maintenance and frequent plant shutdowns. Maintenance Managers agree that standard solutions available on the market are not sufficient for their needs. Rotors and breaker bars must regularly be replaced with new ...
ByCastolin Eutectic GmbH based in Kriftel, GERMANY