- Home
- Applications
- north america
- material sampling
Refine by
Material Sampling Product Applications In North America
31 applications found
An important property of an optical component is the variation of the refractive index of the material from which it is made, broadly referred to as homogeneity. Material inhomogeneity causes variation of the refractive index in a glass, which can be in the form of sharp, cord-like regions called striae or it can occur as a gradient of the refractive index through a larger region of the sample. Material index variations must be qualified to ...
ByZygo Corporation - AMETEK, Inc based in Middlefield, CONNECTICUT (USA)
Premium
When raw materials are purchased it is critically important to verify that the correct materials have been received for quality, regulatory, and economic reasons. Often these raw materials, such as food or pharmaceutical ingredients, are transported in plastic bags or paper packaging. Packaging can be opened to perform a verification test using analytical techniques such as assays or infrared spectroscopy. ...
ByGalaxy Scientific Inc based in Nashua, NEW HAMPSHIRE (USA)
One of the most frequent applications for furnaces is the ashing of food and feedstuff samples – Carbolite’s AAF ashing furnaces remove all organic material from a sample through heating in air. The objective of the test is often to establish the total mineral content or is used as an intermediate step in sample preparation to allow subsequent characterisation by elemental analysis. ...
ByCarbolite Gero Ltd - part of Verder Scientific based in Hope, UNITED KINGDOM
Premium
Raman spectroscopy is rapidly growing in popularity as a tool for general chemical analysis. From incoming raw materials for production to final quality control measurements, Raman’s ability to provide qualitative and quantitative information increases its utilization in a variety of ...
ByB&W Tek based in Plainsboro, DELAWARE (USA)
Safe and effective cleaners for all firearms including black powder and muzzle loaders. Quickly and easily removes carbon deposits, powder residue, bore foulants, oxidation stains, and old oil and grease deposits. Unsurpassed detergency on carbon blue and stainless ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
Premium
Raw material identification and verification is a regulatory requirement for pharmaceutical manufacturers. ...
ByB&W Tek based in Plainsboro, DELAWARE (USA)
Premium
The disposal of hazardous waste requires special handling to ensure that safety and regulatory requirements are met. Preparing the waste for incineration or burial requires equipment that is durable and reliable so that the materials are processed safely and in accordance with the regulatory ...
ByGranutech-Saturn Systems based in Grand Prairie, TEXAS (USA)
Title : Preliminary Sampling Methodology and Analytical Procedures for Ambient Sulfur Hexafluoride, Corporate Author : ARMY MEDICAL ENVIRONMENTAL ENGINEERING RESEARCH UNIT EDGEWOOD ARSENAL MD Personal Author(s) : Luckan,Susan K. ; Cooper,William J. Report Date : JAN 1973 Pagination or Media Count : 23 Abstract : A preliminary evaluation of techniques of sampling and gas chromatographic analysis for low levels of sulfur hexafluoride was conducted to determine the most ...
ByAnalytical Specialties, Inc. based in Naples, FLORIDA (USA)
BESTMIX supports food producers in creating innovative and competitive products with the necessary quality guarantees and correct ...
ByBESTMIX based in Maldegem, BELGIUM
Effective cleaning of machined or formed parts is a key step in all manufacturing processes. At IPC, we understand for a surface to be successfully plated or painted, it must first be free of contaminants. Our cleaners remove dirt, cutting oil, metal fines, flux, and other particulates from stamped metal and precision parts without the hazards associated with solvents. An economical 1-2% concentration in water is effective for most cleaning applications. Our cleaners are also proven in removing soils from filter ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
Our precision cleaners provide consistent results with every use and leave surfaces completely clean. Our products have long been used in pre-sanitization washes of optical devices such as fiber-optic glass, microscope and telescope lenses and light detention instruments. Machining oils, burrs, metal fines, and other soils are easily removed from glass or quartz ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
We understand how critical it is to get the industrial cleaning done so your plant can continue operating at peak efficiency. Our cleaners remove dirt, grease, oil, metal fines, flux, and other particulates from stamped metal, parts and equipment without the hazards associated with solvents. Our cleaners are also proven in removing soils from filter membranes used in wastewater treatment ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
This method allows the direct measurement of low levels of sodium without prior extraction procedures, which minimises possible sources of contamination. ...
ByBWB Technologies Ltd. based in Newbury, UNITED KINGDOM
Our full line of free-rinsing precision cleaners are effective in a wide variety of cosmetic cleaning applications. An economical 1-2% concentration in water is effective for most cleaning applications. Typical uses include removing oils, dyes, fragrances, gels, titanium dioxide, silicons, petrolatum, paraffins, emulsifiers, insoluble salts and oxides. Use to clean hard surfaces including stainless steel, ceramics, plastics and glassware. Our line of cleaners can deliver the critical/precision cleaning needed to ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
Our cleaners are used in the manufacturing of semiconductors, flat panel displays, CDs, DVDs, and many other electronic items. They remove emulsions, particulates, oil, organic and inorganic contaminants from quartz, wafers, glass, silicon, ceramics, and metals. When rinsed properly our products leave no residue and your precision parts are ready for further ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
Powerful, earth-friendly cleaners available in a wide range of formulas to meet specific cleaning requirements for reusable instruments and equipment prior to sterilization. These cleaners are designed to quickly and efficiently remove blood, feces, urine, mucus, fat, sweat, tissue, and other biological debris. Common uses include cleaning diagnostic and surgical instruments, life-support devices, hospital furnishings, and institutional ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
Whether you need to remove biological debris, fingerprints, protein, starch, or dye, our cleaners provide consistent results. An economical 1-2% concentration in water is effective in most cleaning applications. Our laboratory cleaners are excellent for use on flasks, pipettes, slides, stainless steel, plastic, and other laboratory equipment and surfaces. When rinsed properly, our cleaners leave no ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
Our precision cleaners provide consistent results with every use and leave surfaces completely clean. Our products have long been used in pre-sanitization washes of implantable medical devices and prosthetics such as knees, hips, pins, screws, and tubing. Machining oils, burrs, metal fines, and other soils are easily removed from stainless steel, titanium, ceramic and other metal and plastic ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
IPC offers a full line of precision cleaners that provide consistent results with every use and leave surfaces completely clean. An economical 1-2% concentration in water is effective in most cleaning applications. Typical uses include removing protein, starch, grease, fat, gum, oil and baked on soil from processing equipment, lines, and filter ...
ByInternational Products Corporation based in Burlington, NEW JERSEY (USA)
Pendar Technologies offers a suite of products for chemical intelligence and material analysis. Our user-friendly systems can rapidly validate and analyze chemicals for incoming inspection, process & quality control, forensics, or other industrial ...
ByPendar Technologies based in Cambridge, MASSACHUSETTS (USA)