Show results for
Refine by
So2 Product Applications In Romania
32 applications found
Premium
Process monitoring at a sulfuric acid plant requires good and reliable detection of, among other things, sulfur dioxide (SO2) in gas phase. This can be a challenge due to high concentrations of SO2, high temperatures, and high pressure. Monitoring may be needed at several locations in the process where SO2 concentrations may vary from a few mg/m3 to several percent by volume. ...
ByOPSIS AB based in Furulund, SWEDEN
ByAMETEK Process Instruments based in Pittsburgh, PENNSYLVANIA (USA)
Premium
An alternative that makes it possible to continue using high-sulfur oil as fuel is to install SO2 scrubbers that clean the flue gases to the same level as if the ships were fueled with low-sulfur oil. However, the scrubbers must be monitored by measuring the ratio of SO2 to CO2 concentrations. Here, OPSIS has a certified, cost-effective, and reliable ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Among other things, nitrogen oxides (NOX) and sulfur (sulfur dioxide, SO2) are regulated. OPSIS has the instruments to monitor the ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
In the case of emissions from ships, it may be of particular interest to monitor sulfur dioxide (SO2) levels near the stacks to confirm that low-sulfur oil is being used or that desulfurisation is activated. ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Method allows determination of mass concentration of total sulfur dioxide (sulfurous acid and its salts, food additives E220–E228) in wine, wine materials, beer and beer products by capillary electrophoresis (CE) using capillary electrophoresis system “CAPEL® -105M”. The mass concentration of total sulfur dioxide is regulated by normative documents to be held within 100– 400 mg/L for different types of wine and wine materials and within 20–50 mg/L for beer products. According to ...
ByLumex Instruments based in Mission, BRITISH COLUMBIA (CANADA)
Premium
OPSIS non-contact monitoring solutions, based on either DOAS or TDL techniques, are very well suited for applications in the mining and smelting Industries, as the flue gas conditions often involve high temperatures and high dust ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Monitoring the air quality at and around airports can be done for several reasons. It may be a question of monitoring the pollutants that employees and passengers are exposed to, but it may also be a matter of studying the contribution of aviation and ground traffic to pollution. Regardless of purpose, monitoring can be a challenge. The location of the measurement site must be representative. A large number of gaseous components need to be monitored with high accuracy and high ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Various types of sulfur compounds often arise during the production of paper pulp. There are emission limits and monitoring requirements, often expressed as total reduced sulfur, TRS. TRS includes hydrogen sulfide, H2S, and the sulfur compounds methyl mercaptan, dimethyl sulfide, and dimethyl disulfide. OPSIS offers systems to monitor both H2S and ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Process monitoring and monitoring of emissions from aluminium smelters can be a challenge due to high concentrations of for example hydrogen fluoride (HF) and dust. The use of sampling systems in such environments requires a lot of maintenance and is therefore costly. Such systems can also be unreliable. OPSIS offers better ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
The high temperatures in glass manufacturing can make it difficult to monitor gas concentrations for process control and emissions monitoring. However, OPSIS offers monitoring systems that handle the high temperatures in an excellent way. ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
OPSIS offers monitoring systems for continuous emissions monitoring and process control at power plants. The systems meet and exceed high demands on availability, speed, versatility, and low operating ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Monitoring in raw gas places high demands on the instruments. The temperatures are high and the gases are often reactive. There may also be high dust levels. In order to control flue gas cleaning, the monitoring systems must also be able to react in near real time. However, these are no problems for OPSIS non-contact monitoring systems, which work excellently in these circumstances, with high availability and low operating ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
There can be several purposes for monitoring the air quality in an urban area. If the aim is to assess what the residents are exposed to in the worst case, a so-called street-level monitoring is carried out. If the aim is to monitor the general levels of air pollution and follow up long-term trends, you should instead monitor further away from the busiest roads, for example at roof level. ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Challenging conditions for gas analysis at waste-to-energy facilities. Process and emissions monitoring at waste-to-energy plants or plain waste incineration plants can be a challenge. A large number of gas components need to be monitored with high accuracy. The flue gas is often aggressive and has high dust and moisture content. Close to 100% uptime is required, the monitoring system must be easy to maintain, and it must be able to be calibrated quickly. The OPSIS monitoring system handles all these challenges ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Demanding monitoring environment at cement industries. Process control and emissions monitoring at a cement plant can be a challenge due to high dust levels and corrosive gases. OPSIS offers gas analysis systems that can handle these environments and that have high accuracy, short response times, and long maintenance ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
'Chemical industry' can comprise many types of industries, for example refineries, paper mills, fertilizer production, and sulfuric acid plants. Each individual industry may have its own special needs and special environments, but there are also many common factors. Regardless, process control and emissions monitoring at chemical plants can be challenging due to for example toxic, aggressive and/or explosive gases, and high temperatures. The use of extractive systems in such environments requires a lot of ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
The nature of steel manufacturing processes places severe limitations on the monitoring methods that can be used. Aggressive environments combined with high levels of particulates and gases make the choice very ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Gas analysis in brick manufacturing: Process control and emissions monitoring at brick plants can be challenging due to high concentrations of hydrogen fluoride (HF) and dust. The use of extractive monitoring systems in such environments requires a lot of maintenance and can still cause major operational disruptions. However, the contactless technology offered by OPSIS solves the ...
ByOPSIS AB based in Furulund, SWEDEN
Premium
Monitoring of fugitive emissions from industrial facilities. Most of the OPSIS gas analysis systems are based on monitoring methods with open measurement paths. This provides a perfect tool for monitoring the air quality and detecting any gas leaks from industrial facilities so that staff and nearby residents can be alerted and measures can be taken ...
ByOPSIS AB based in Furulund, SWEDEN