Refine by
Ftir Product Applications In Texas
34 applications found
The United States Environmental Protection Agency (EPA) has two stack testing methods for FTIR gas analyzers. Method 320 is an FTIR method for measuring wide range of organic and inorganic pollutants. ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
In this process, the Gasmet™ FTIR Gas Analyzers can be used to measure the emissions into the atmosphere and also monitor the efficiency of the scrubbers. ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
At nitric acid manufacturing plants, the Gasmet™ FTIR Gas Analyzer can be used to measure several gaseous components from the process stream for purposes of process control. ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
The Gasmet™ GT5000 Terra portable FTIR Gas Analyzer provides reliable identification and concentration measurements of hazardous gases in 60 seconds or ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
As phosgene is very poisonous, even small gas pockets in serviced equipment may be dangerous to maintenance personnel. Gasmet™ FTIR Gas Analyzers are ideal tools to monitor point sources of phosgene. ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Type approval regulations like ECE-R100 and FTIR technology in GT5000 Terra align with safety mandates. ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Multicomponent analysis of exhaust gases can be performed with a Gasmet™ FTIR Gas Analyzer with a response time (T90) of one second. The winning combination is the result using of a small volume gas sample cell, a powerful sample pump and a fast detector with liquid nitrogen cooling. ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Typically only a few components are measured but fourier transform infrared spectroscopy FTIR technology allows the measurement of all ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Detect Thermal Hazards Early and Design Safety Into The Chemical Process. We must ask ourselves: How much heat will be generated under normal conditions? How will a change in condition, controlled or uncontrolled, change the rate of heat generation? Can our process equipment handle removing the heated generated? Answering these questions with speed and accuracy is necessary to ensure safe and efficient design and scale-up of synthesis ...
ByMettler - Toledo Int. Inc based in Greifensee, SWITZERLAND
Process Development in the chemical industry requires a profound and comprehensive knowledge of the processes involved and is governed by a triangular relationship between 'Economy - Safety - ...
ByMettler - Toledo Int. Inc based in Greifensee, SWITZERLAND
IR-Spectroscopy is not limited to gases, solid materials and pure liquids but also facilitates the measurement of solutes in aqueous media. Though, due to the strong and temperature dependent absorption of water, the usage of conventional IR-transmission and ATR accessories is not very suitable for the analysis in water. The CONFOCHECK is a dedicated FT-IR system for the fast, easy and sensitive analysis of aqueous samples. Using this system, preparing, measuring and evaluating any aqueous sample takes typically ...
ByBruker Corporation based in Billerica, MASSACHUSETTS (USA)
Today, pharmaceutical and fine chemical companies face major challenges posed by globalization, environmental regulation, and shortened product life cycle that affect all aspects of their business. The research and development of an optimized chemical synthesis route must be carried out in less time and with less chemical waste to ensure a robust and economic process that can be efficiently scaled to manufacturing while meeting constraints related to product yield and purity, process and worker safety, and ...
ByMettler - Toledo Int. Inc based in Greifensee, SWITZERLAND
Premium
Machine condition monitoring using oil analysis is widely practiced by virtually every segment of modern industry that maintains large, expensive, oil-lubricated machines. In many cases, especially in smaller plants or enterprises, samples are sent to commercial oil analysis laboratories that can help monitor machinery ...
ByAMETEK Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA)
Sampling and analysis of fire effluents is an important part of assessing both the environmental impact and the threat to life caused by fires. Detailed knowledge about the composition and concentration of fire effluents is required to gain a good understanding about the potential impacts of fires and for efforts to diminish these impacts. Testing the composition of these fire effluents presents a challenge for the analytical equipment used to measure the gases. The amount of species and concentrations of interest ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Premium
Power plants are expected to operate 24 hours per day, 7 days per week. Downtime and equipment derating (when a generator fails to deliver power at its rated capacity) can cost a power plant thousands of dollars per hour. The cost of replacing failed equipment is also extremely high. Vibration analysis by itself is not enough to anticipate catastrophic failures. Oil analysis is often able to detect problems at a much earlier stage than vibration analysis. This is why more and more power plants are bringing oil ...
ByAMETEK Spectro Scientific based in Chelmsford, MASSACHUSETTS (USA)
Typical modern printing processes utilize solvent-based dyes. The evaporation of the dye solvents into the ambient air during the printing process may expose the workers to various chemicals. Depending on the type of solvents in case, the solvents have different long term exposure limits, which should be obeyed. Component specific measurements are necessary to protect the workers from exposure while avoiding unnecessary interruptions to the printing process from false ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
To meet the requirements of new regulations and to protect the environment effectively, industries need techniques that enable the analysis of elements at lowest concentration levels. Bruker X-ray fluorescence (XRF) analysis is the most suitable analytical technique for handling different kinds of materials. Bruker’s XRF, ICP-MS, GC, TOF-MS, FT-IR, CBRNE products and applications help you to monitor contaminated land efficiently and quickly, to determine hazardous elements in the air and water, as well as to ...
ByBruker Corporation based in Billerica, MASSACHUSETTS (USA)
Sea cargo containers and wooden packing materials are fumigated to control the spreading of pest animals and micro-organisms. Fumigant gases are toxic and measurements are carried out as a health and safety precaution. Measurements are required by e.g. customs inspectors prior to opening containers, making the shipping companies responsible for carrying out measurements. Products shipped in containers may release VOCs from e.g. solvents and glues used in manufacturing process. The concentrations of vapors may be ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
Titanium dioxide is the most important white pigment used in the polymer industry. It is widely used, because it efficiently scatters visible light, thereby imparting whiteness, brightness, and opacity when incorporated into a plastic ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND
The mining industry uses chemicals as ‘flotation’ agents in the recovery of sulphide minerals containing metallic elements (e.g., copper, nickel, silver, gold) from ore slurries. Sodium ethyl xanthate (SEX) is one of most common flotation agents, and it decomposes to form ethanol, carbon disulfide CS2, and Carbonyl Sulfide COS. These harmful gaseous compounds must be monitored from the indoor air at the enriching ...
ByGasmet Technologies - a Nederman company based in Vantaa, FINLAND