Refine by
Calorimeter Articles & Analysis
17 articles found
The recently purchased embedded calorimeter, strength tester, pulverization degree gauging tool and other tools in the laboratory provide us with a much more targeted instructions for readjusting and also investigating the chicken feed pellet maker, which can recognize real-time testing of after-sales production pellets, and also make use of sophisticated tools to detect users. ...
The common methods for analyzing microplastics are as follows: Infrared spectrometer Pyrolysis Gas Chromatography (Py-GC) Energy dispersive X-ray fluorescence spectrometer Differential scanning calorimeter Dynamic particle image analyzer If you have any questions about microplastics testing, feel free to contact ...
ByMatexcel
The HHV is analyzed with a bomb calorimeter and converted to the LHV. It is also possible to calculate the heating value via chemical oxygen demand (COD), total volatile solids (TVS), and elemental composition. ...
The bio-oils produced by the condensation of vapours are systematically analysed using an elemental analyser, calorimeter, gel permeation chromatograph, densimeter, viscometer, and thermal analyser. ...
They were looking to have an online, real time measurement with a calorimeter type analyzer. They wanted to determine the BTU content at any given time so their customers would know the fuel energy of their samples. ...
The company’s initial preference was for a Calorimeter type measurement with fast response and GC measurement only where additional gas make‐up information was required. ...
Cryoporometry was carried out using a differential scanning calorimeter (DSC). Two volume fractions - 0.1% and 0.3% - of a treated cellulose fibre were investigated. ...
Cryoporometry was carried out using a differential scanning calorimeter (DSC). Two volume fractions - 0.1% and 0.3% - of a treated cellulose fibre were investigated. ...
It has been found that the cured film shows good flame retardancy when the MDMPE is at 30% additive level. The cone calorimeter results show that the heat release rate decreases in comparison with the pure PUA. ...
The authors relate fire performance (UL 94, OI, NOI) and thermal analyses (TGA and thin film FTIR) results to cone calorimeter fire growth curves, in an attempt to extract meaning beyond peak heat release rate and time to ignition. ...
The fuel in trays is placed at three locations (front, back, and center) within the room enclosure as well as directly under the calorimeter hood. The measured heat release rate (HRR) is found to vary substantially when a fuel package consisting of different quantities of ethanol is placed at different locations within the room. ...
This study addresses the fire performance of polypropylene compounded with different flame retardants in the cone calorimeter tests and UL-94 burning tests. The parameters measured include heat release rate, time to ignition, smoke, and CO/CO2 yields, on the basis of which fire hazard analysis is carried out. By injection-molding different burn-rated polypropylene composites into ...
Effect of water mist on the small-scale solid fuel PVC (poly vinyl chloride) fire in a confined space has been studied experimentally using a cone calorimeter. In this study, the combustion characteristics of PVC, and the interaction between the water mists and the diffusion flame in a confined space with proper ventilation control are studied under various conditions in the cone ...
Synthesis routes based on ethylene-vinyl acetate copolymer (EVA) or thermoplastic polyurethane (TPU) masterbatches of organoclays strongly diminish the darkening of the PVC compounds. Cone calorimeter experiments do not show remarkably improved flame retardancy properties of PVC filled with ...
The flame retarding behavior of these samples is measured by cone calorimeter. The thermal behavior of samples has been studied by differential thermogravimetry (DTG) and thermogravimetry (TG) in air. ...
Results of tolerance time from Stoll criterion method are also compared with Henriques burn damage integral from two skin models between constant–flux exposures in TPP calorimeter. Investigations have been conducted to find the effects of structural parameter, air pressure, and air layer thickness on the thermal performance of the selected FR fabric determined by the newly ...
A rather simple water mass flow calorimeter was designed to study this phenomenon under different experimental conditions. ...