Refine by
Grease Testing Articles & Analysis
21 articles found
Replace worn-out wheels or bearings to prevent excessive friction and premature failure. Braking System: Test and inspect the braking system for proper functionality, including emergency brakes and parking brakes. ...
This study was designed to evaluate the impacts of Ana-Zyme P on biogas generation in a mesophilic dairy manure digester supplemented with fats, oils, and greases (FOG). Testing was a BMP style test at 97°F (36°C) run for 56 days. ...
The odors detected in the lounge area were definitely hydrogen sulfide-based odors, so the grease interceptor was tested for sulfide levels. The sulfides in the liquid phase of the grease interceptor outlet measured more than eight milligrams/liter concentration. ...
Numerous storage tanks consolidated grease that required expensive removal via pump trucks four times per week. ...
BioCOPE’s product performed successfully in a rigorously controlled grease field test designed by Brown and Caldwell Engineering for the City of San Diego. When the pounds of Fats, Oil and Grease (FOG) removed were divided by the cost of the products, BioCOPE’s score was three times higher than the other products ...
These personnel or other well trained technicians draw samples, run the tests using on-site oil analysis, confirm the alarms, create additional action items, and complete the assigned work orders. ...
The fluid in the tank wais comprised of septic waste from Porta-Potties as well as grease pumped from commercial grease traps. Two tests were conducted. FIRST TEST: 400 gallons of septic waste containing F.O.G. was pumped from a holding tank into a 500-gallon test tank. ...
This mobile unit can process manure, food waste and FOG (Fats, Oils and Greases), and is designed to be used as a test-bed to explore feedstock recipes and the biogas potential of mixed food/manure feedstocks. ...
Water is a very strong absorber in the mi d infrared (I R) regio n where o il is measured. We see the effect of infrared absorbance when a cold bucket of water left in the sun is quite warm by afternoon due to the absorption of infrared energy as heat. When measuring part per million (ppm) oil levels with mid IR, the water absorbs so much of the infrared energy that the signal becomes saturated ...
For the treatment facility that is imposing the limits, an on-site test allows them to catch offenders. While they ultimately require a testing lab to verify the offense, only the samples that are over the limit need further testing. Hopefully, most of the samples will be within the limit saving a significant amount on laboratory ...
For the treatment facility that is imposing the limits, an on-site test allows them to catch offenders. While they ultimately require a testing lab to verify the offense, only the samples that are over the limit need further testing. Hopefully, most of the samples will be within the limit saving a significant amount on laboratory ...
A White Paper entitled, “Solvent Choices for Infrared Testing of Oil and Grease in Water” was recently published by Wilks Enterprise, Inc. ...
A 300 foot section of 6" sewer line was clogged with grease. After the City Personnel broke it free and flushed it towards the treatment plant, a gallon of BYO‐GON PX‐109 was added to the line. The operators at the plant were notified that in 21 hours, 300 feet of grease and other debris would be going to the plant. The operators were ready, but the ...
Wilks InfraCal TOG/TPH Analyzers provide accurate, on-site analysis to help regulators and industry reduce the discharge of fats, oil and grease in wastewater. On-site testing with the portable mid-IR InfraCal Analyzer gives results in 10 minutes and eliminates the wait for off-site lab results. ...
Wastewater professionals who are enforcing industrial effluent standards for fats, oil and grease (FOG) either must perform numerous gravimetric tests or spend a considerable amount of money with a contracted testing laboratory. ...
Static sheen tests were conducted on the water discharged from CETCO’s equipment throughout the project, and the water continuously passed the test. Infrared oil and grease measurements were also performed on the treated water, and all results were well below the discharge criteria. An independent laboratory tested samples of the ...
The process is shown above. Fluids were tested for oil and grease throughout the process. When oil and grease levels from the platform’s existing system approached 25 ppm, the fluids were diverted to CETCO Oilfield Services’ system. ...
These tests were conducted to determine the effectiveness of grease removal and digestion by installing the DO2E Grease Digester and traditional chemical additives. The Little John Grease Digester was installed in test sites 1 and 2 and the patented formula FC 100 was applied to test locations 3 ...
The grab samples performed by the local sanitary district exhibited high levels of BOD, COD and oil and grease levels in the discharge water. The problem was traced back to their compressor condensate discharge. The company has 14 – 100 to 200 HP compressors that significantly contributed to their discharge limit violations during the high humidity summer months. The ...
During a day's operation, up to 100 gallons of oil and grease from open gears, drive chains, bearings and other sources get washed into wastewater flumes by cooling water. ...