Pipe Clamp Articles & Analysis
22 articles found
Both measure flow by transmitting and receiving ultrasonic waves in a pipe. Doppler flowmeters can measure dirty liquids, while clamp-on transit time ultrasonic flowmeters primarily measure clean liquids.Both utilize a clamp-on flow sensor to detect flow in closed pipes. ...
Both utilize a clamp-on flow sensor to detect flow in closed pipes. Clamp-on ultrasonic flowmeters are a unique measurement method and are currently the dominant type. ...
Ultrasonic flowmeter mainly consists of flowmeter body, ultrasonic transducer and its installation parts, signal processing unit and flow computer components. For on-site contact and clamp-on flowmeter, the pipe where the transducer is installed can be used as the meter body, the transducer of the contact flowmeter is directly in contact with the measured fluid, ...
Ultrasonic Flow Meters for Low-Flow Applications ✅ Best for: Clean or slightly contaminated liquids, especially in large pipes High sensitivity to low flow rates, especially with Doppler or transit-time ultrasonic meters designed for small-diameter pipes. Non-intrusive clamp-on models avoid pressure loss and work well for retrofits. Lower ...
Operation: Transducers: Two ultrasonic transducers are mounted on the pipe, either in a clamp-on (external) or inline (internal) configuration. ...
The change in the speed of sound is used to calculate flow. Advantages:Non-intrusive (clamps onto pipes, no contact with the sludge). Suitable for both clean and dirty liquids. ...
These are the only duckbill valves engineered with a sloping bottom for installations where the pipe is close to the floor of the outfall or manhole. These valves are engineered to crack open at 1 to 2 inches of head pressure. ...
Methods of disassembly of the pressed screw and circular row of the oil manufacturing machine: Remove the protective cap, round nut, adjusting bolt, cone bearing and thrust bearing on the screw press, clamp one end of the screw shaft with pipe clamp or other tools, and insert the lever on the other end into the hole of the lock nut by turning, ...
A sparge nozzle was installed at the bottom of each of the basins to receive the waste gas stream, which is piped directly from the hydrogen plant. The system uses a flow-through pH sensor and pH transmitter/analyzer to control the amount of CO2 sparged. ...
The versatility of the clamp-on ultrasonic meter made it a perfect tool for the small, often cash-strapped, water company. Simply clamp the sensors onto the outside of the water pipe and extremely accurate measurement was now possible–no need for costly system shut downs, pipe cutting and plumbing. ...
” Industrial duct comes in multiple styles (e.g., spiral, welded flanged, vanstoned flanged, and clamp-together). What is Spiral Duct? Spiral ductwork is a relatively inexpensive style of duct pipe that is named after its manufacturing method. ...
Ultrasonic flowmeters are ideal for water and other liquids. Clamp-on ultrasonic flow meters achieve high accuracy at low and high flows, save time with no pipe cutting or process shutdown, and are not affected by external noise. ...
Although a major benefit of the technology is that it is non-invasive and can be clamped to the outside of the pipe, an inherent challenge with ultrasonic clamp on liquid flow meters is finding the best location to measure the liquid. ...
Application Steel cast pipe with 700 mm diameter Full filled Existing EMF in pipeline defective Definition of tasks Cost-efficient installation of the new flow measurement Defective EMF should not be removed if possible (costs) No interruption of running processes Solution A permanent flow measurement transmitter Type NivuFlow 750 in combination with a flow ...
The most commonly used accessories are Crimp and Clamp tools, which correspond to crimp and clamp rings. The Crimp tool is used to form a 360 degree compression around the crimp ring to ensure that the pipe and fitting are securely tightened to one another. ...
Our valves come in flanged and non-flanged versions and can be clamped or drilled onto pipes depending on the scenario. A thimble plate (straight or angled) is used to attach the valves headwalls - even square cuffs are ...
Its TP10 ultrasonic thermal energy meter is a non-intrusive and robust instrument which accurately measures flow, temperature and thermal energy consumption (BTU). The transducer can easily be clamped onto any pipe size without cutting the pipe or shutting down the flow. ...
To maintain production without shut downs Petrobakken contacted Seidlitz Engineering of Cochrane, Alberta to help find a solution to their wax off problem. Seidlitz specified clamp-on ultrasonic meters because they work from outside the pipe without obstructing flow. ...
The Cougar ROV cut loose and replaced two 500 foot 1-1/2” stud link restraining chain bridals. The pipe had to be cleaned and obstructions cut loose for the installation of new pipe clamps in three places. 1-1/2 tons of flotation was added at each clamp location. Two 1-1/2” stud link chain bridals were added at the ...
The company appreciates the versatility of Sierra’s meters with their ability to clamp on to any size pipe. Flowmeters are made from a variety of materials, from galvanized steel and cast iron pipes to PVC. “Two pipe clamps and you’re done,” said Eric Furtado, the lead water operator from ...