Polymer Pump Articles & Analysis
22 articles found
Chemical company in Estonia chooses SAMOA UP20 pump to handle their fluids. The user, a chemical company based in Estonia, was a looking for a chemical pump, able to dispense around 20 m3/ hour of a polymer, which is inside a Flexitank. Polymer is a medium viscosity fluid, of around 1.500 cPs. In this particular case, since the ...
It sets Techase Multi Plate Screw Press, polymer station, sludge pump, electric control cabinet, spray tank, electric generator as a whole. ...
You should also find out what you will need to provide during the testing period, such as power supply, quantity of test material, pumps, polymers, or ventilation. Test equipment is able to comply with safety requirements, so be sure to indicate any safe handling or hazardous situations that can arise during operations. ...
Approach used / Answer given The Châtres Town Council commissioned GEB Conseil to provide it with an integrated solution, including: A flocculating agent mixing cabinet, with integrated pumping, dilution, and treatment flow rate control, Treatability tests and an option to select the mixture to be used, Set-up and start-up on site, Training for council workers. ...
Without good flocculation, the sludge cannot be mechanically thickened and dewatered using a belt filter. When continuously mixing polymer powder, a precise water/powder ratio is required and there is a risk of lumps forming if the powder wetting and mixing process is not adjusted to the correct and optimal setting. ...
The heart of the BaiPod Container range is represented by the BaiDec 65Lv high performance centrifuge decanter with all necessary ancillaries such polymer preparation station, control panel with PLC logic completely automated operation, feed pump, polymer dosing pump, flow meters, screw conveyor, interior lighting with 6 double ...
PCPC burn-off oven removed 4,240 lbs. of styrene polymer in compliance with local environmental laws. The Problem: ARCO Chemical Company's Beaver Valley plant in Monaca, PA, a manufacturer of styrene-based plastics, was experiencing severe problems and expense with the periodic cleaning of their large 20' long heat exchangers (condenser). ...
The high density topcoats, up to 100 lb/cu ft (1600 kg/cu m), are comprised of heavy, abrasive aggregates — coarse particulates of sand and marble — blended with pigments in an acrylic polymer binder. The material caused the shaft seals of Master Wall's blenders to wear and leak. ...
The solution: The sludge was removed by divers using special pumping equipment. The sludge, together with a lot of water, was pumped to street level, beside the Rijksmuseum. There, in a small garden, after being mixed with polymers, the sludge was pumped into Geotube®for containment and quick dewatering. ...
The remediation works in Svartsjoarna involves dredging of approx 260.000 m1 of mercury contaminated fibre sediments. These sediments are pumped to the landfill nearby, specially prepared for this project where it is treated with polymers (flocculants) and pumped into Geotube It is the first time that this new technology is used in Sweden and ...
Raw water is oxidized with an iron rich coagulant is added to the water prior to treatment to promote maximum removal of the arsenic and manganese. A polymer dosing pump is also included in the treatment system for effective process operation. The flocculated material after the polymer addition is captured in the ADGS+ media. The filters are ...
The DDP also produces a dry cake with less polymer; a winner in every aspect. In addition to the DDPTM press, BDP provided a complete system including: feed pump, polymer make up/metering system, discharge conveyor, venturi mixer, wash water pump and air compressor. ...
The system included a control panel, hydraulic system, polymer system, sludge pump, wash water pump and discharge conveyor all conveniently mounted on the trailer. ...
In addition to the press, BDP provided a complete system with control panel, polymer mixer, hydraulic system, wash water pump, and discharge screw conveyor. ...
This configuration provides maximum operator flexibility, high throughput rates, and decreased polymer usage. In addition to the press, BDP provided a complete system with control panel, polymer system, hydraulic system, wash water pump, discharge screw conveyor, truck load out conveyor, and assistance in the room layout design. ...
This configuration provides maximum operator flexibility, high throughput rates, and decreased polymer usage. In addition to the press, BDP provided a complete system with control panel, polymer pump, hydraulic system, and shower water. ...
The skid is outfitted with all the necessary equipment for processing the solids: control panel, belt press, polymer unit, wash water booster pump, hydraulic unit and venturi mixer. ...
However, to ensure that we meet our consent levels we operate a polymer flocculation plant which uses a non-ionic floc to assist in the settlement of solids. ...
From there it was pumped back into the East River without any secondary treatment Polymer Mix Plays Key Role An important component of the Geotube system is the evaluation of an appropriate polymer program using the TenCate RDT Rapid Dewatering Test and the TenCate GDT Geotube Dewatering Test to optimize the dewatering process. ...
Two 100-ft. long test bags were used, along with a chemical treatment pump, tanks, and pipe manifold to allow for required polymer injection Slurry was pumped directly into the bags from the preparation plant underflow. ...