Refine by
Selective Electrode Articles & Analysis
55 articles found
As the cooking solution for alkali such as Ca (OH) 2 or Na0H solution, the slurry are alkaline, so the electromagnetic flowmeter is mostly used in high-temperature-resistant polytetrafluoroethylene lining and split-type structure type. In the choice of electrode materials to consider the selection of corrosion-resistant materials. ...
PU offers excellent resistance to wear and corrosion and is often used for measuring media containing particulate matter and exhibiting some corrosiveness, such as sewage. Consider the electrode material: The electrode comes into direct contact with the measured medium, so the appropriate material must be selected based on the medium's ...
Corrosive liquid: Since only the lining and electrodes of the sensor part are in contact with the measured liquid, as long as the electrode and lining materials are reasonably selected, the split electromagnetic flowmeter can be used to measure corrosive liquids. 2. ...
Corrosiveness The chemical properties of the measured fluid are crucial to the material selection of the electromagnetic flowmeter. If the fluid is highly corrosive, such as acid, alkali or salt solution, corrosion-resistant electrode materials and lining materials need to be selected. ...
The detection part mainly includes electrodes and interference adjustment parts. Since the electrodes are in direct contact with the measured medium, they must have strong corrosion resistance. ...
At the same time, some liquids can penetrate PTFE, causing short circuits and corrosion to flowmeter components; ②PFA, which has lower permeability than PTFE, but is easily deformed when temperature and pressure change; ③Ceramic, which is suitable for a variety of application conditions, but this material is sensitive to temperature fluctuations and pipe stress; ④Rubber, neoprene or natural ...
The minimum flow rate that can be measured by a vortex flowmeter is limited by the Reynolds number, the flow rate of the fluid and the signal-to-noise ratio (frequency interference). Vortex flowmeter selection 1. When selecting the flowmeter, the minimum measurable flow rate value of the selected flowmeter should be lower than the minimum flow ...
The normal operating flow rate should be at least 50% of the meter’s full-scale range to ensure accurate measurement. 3. Electrode and Lining Selection For media that do not cause crystallization, caking, or scaling on the electrodes, standard electrodes should be used. Otherwise, scraper electrodes are ...
The normal operating flow rate should be at least 50% of the meter’s full-scale range to ensure accurate measurement. 3. Electrode and Lining Selection For media that do not cause crystallization, caking, or scaling on the electrodes, standard electrodes should be used. Otherwise, scraper electrodes are ...
However, installation and wiring must be done carefully to avoid signal interference. The electrode material should be selected based on the corrosiveness of the measured medium. ...
The normal operating flow rate should be at least 50% of the meter’s full-scale range to ensure accurate measurement. 3. Electrode and Lining Selection For media that do not cause crystallization, caking, or scaling on the electrodes, standard electrodes should be used. Otherwise, scraper electrodes are ...
Additionally, adding a necked grounding ring during installation can greatly improve the wear resistance of the liner. Selection of Electrodes When selecting electrodes for electromagnetic flow meters in the papermaking industry, two main factors are considered: corrosion resistance and scaling prevention. ...
Selecting a wastewater electromagnetic flow meter involves considering several key factors to ensure accurate and reliable measurement. ...
Applications: Used in slurry applications where abrasion is a concern. 3. Electrode Materials: Electrodes are in direct contact with the fluid and must be conductive and resistant to corrosion. ...
Applications: Used in slurry applications where abrasion is a concern. 3. Electrode Materials: Electrodes are in direct contact with the fluid and must be conductive and resistant to corrosion. ...
In practical applications, in order to prevent the sewage containing solid particles on the lining and electrode wear, the general selection of the sensor caliber is relatively large, and the flow rate of 3m / s below is appropriate, but in order to ensure the symmetrical distribution of the flow rate, to try to extend the length of the upstream and downstream ...
Introduction Argon gas TIG welding, or Tungsten Inert Gas welding, is a specialist technique known for its precision and clean welds. Unlike other welding processes, TIG welding utilises a non-consumable tungsten electrode, and argon gas plays a pivotal role in shielding the weld from atmospheric contaminants. Precision in welding is crucial, particularly in industries where the integrity of the ...
Comprehensive consideration. 1 caliber selection According to the sewage treatment plant to provide the caliber of the process pipeline, pipeline pressure and sewage flow, select the caliber of D = 600mm electromagnetic flowmeter, the site does not need to shrink and expand the pipeline. 2 lining, electrode material selection ...
Electromagnetic flowmeters and ultrasonic flowmeters are alternative options for flowmeter selection in sewage treatment units. For specific sewage treatment units, electromagnetic flowmeters and ultrasonic flowmeters should be flexibly selected according to actual working conditions, such as pipeline diameter, required measurement accuracy, etc., to achieve ...
The customer asked us to evaluate the Electrocoagulation for the removal of Boron and to be able to drain the treated water into the sewer ...