alcohol-sensor Downloads
17 downloads found
Premium
Detcon Model 1000 Series H2S Analyzer consists of two major assemblies: 1. The Model 1000 Series gas sample-conditioning assembly. 2. The Model DM-624 H2S gas sensor (using Alcohol Free - Electrochemical Sensor or Hi-Range Electrochemical ...
Because residual oils on the EC sensor pads, including oil from your fingers, will reduce the accuracy of the sensor, clean the sensor with rubbing alcohol. ...
SERIES U gas detectors utilize unique, patented sensors that are unaffected by moisture, temperature change, or poisons. Dedicated units are available for Hydrogen Sulfide, Sulfur Dioxide, Carbon Monoxide, Ammonia, Diesel/Gasoline Vapors, Total Hydrocarbons, Hydrogen, Combustibles (as Methane), Freons, or Ethylene Oxide and Alcohols. SERIES U ...
Widely used, the Alco-Sensor III (ASIII) is a pocket-sized, handheld breath alcohol tester. This NHTSA approved Evidential Breath Alcohol Testing Device provides a simple, accurate and economical method of determining a subject’s breath alcohol concentration. Standard Equipment- Alco-Sensor ...
The Alco-Sensor IV is an evidential grade handheld breath alcohol tester, providing a simple, accurate and economical method of determining a subject’s breath alcohol concentration with evidential grade accuracy. ...
The Alco-Sensor FST (ASFST) Passive Screener provides precise, accurate, repeatable results on passive breath sample testing. The instrument is designed to offer a simple passive testing procedure for quick screening of a large number of subjects and the capability of measuring the headspace over a solution to identify alcohol in a suspected open container. ...
Data Sheet The MiCS-VZ-87 is an integrated sensor board for Indoor Air Quality monitoring. The MiCS-VZ-87 combines state-of-the-art MOS sensor technology with intelligent detection algorithms to monitor VOCs and CO2 equivalent variations in confined spaces, e.g. meeting rooms or vehicle cabins. ...
A central control panel powers and monitors up to eight combustible gas sensors, while providing automatic calibration of the sensors on a scheduled basis. ...
Premium
It should not be allowed to dry out. However, if this occurs, the sensor may sometimes be rejuvenated by first cleaning the sensor well with Isopropyl alcohol or a liquid spray cleaner such as Windex™ or Fantastic™ and rinsing well. ...
Premium
warning: all monitor/controllers are factory set to operate on 115 vac. before applying power ensure the input power "115/230 vac" selection is correct for your requirements. failure to do so is beyond the responsibility of the myron l company. see section ii.e.2. and figure ii.e.1. warning: ensure power is off while installing electrical equipment. if monitor/controller is installed, ensure the ...
Premium
Cleaning Sensors, 2. pH/ORP, pg. 32). Do not allow pH/ORP sensor to dry out.C. ...
Before calibrating, the electrodes should be cleaned well with alcohol. 2. Immerse the sensor up to the immer-sion indicator on the sensor molding (indicated by arrow in image to right). 3. ...
The temperature sensor signal is supplied to the ADC input. The ADC converts signals of the oxygen sensor and the temperature sensor into codes incoming the microcontroller. ...
ByVZOR
The temperature sensor signal is supplied to the ADC input. The ADC converts signals of the oxygen sensor and the temperature sensor into codes incoming the microcontroller. ...
ByVZOR
These fumes can diffused throw off the sensor’s accuracy. It ise, to never bring the sensor into con-hemical vapor (i.e. glue, alcohol, gaso-on on “Sensor Head Reconditioning”nsors have been affected by chemicalctsurement, the following effects must beof CO2 required for a plant changesount of sunlight available to it. ...
In the WP4, a sample cup, which is sealed against a he sensor block is a fan, a dew point sensor, and an infrared thermome-sor measures the dew point temper-the infrared thermometer measures ure. ...
It works also with temperature probes with 4 wire Pt100, 2 wire Pt1000 or Ni1000 sensors. Some probes are fitted with SICRAM module that acts as an interface between the sensor on the probe and the instrument. ...