anemometer-cable Downloads
18 downloads found
Tools and Materials Needed You will need the following tools and materials to install your anemometer: ? Cable Clips or Weather-Resistant Cable Ties Make sure the clips or ties you use to secure the anemometer cable have screw holes or other means for mounting the cable. ...
Guide the anemometer cable through and free from the grommet. Or in the case of the Vantage Pro2 SIM Box, guide the anemometer cable free of the cable access port by first removing the foam insert and then guiding the cable out of the box. ...
Tools and Materials NeededYou will need the following tools and materials to install your anemometer:• Cable Clips or Weather-Resistant Cable TiesNote: Make sure the clips or ties you use to secure the anemometer cable have screw holes or other means for mounting the cable. ...
Rear access must be provided for fixing of the tightening clamps and connecting the electric cabling. The depth of the units is 94mm and an additional clearance of 8mm should be allowed for the cable connections and strain relief. 4.2 Electrical The WindDisplay utilises a common terminal strip for connections to the anemometers and ancillary ...
This datalogging anemometer automatically records up to 16,000 data points in the field along with time and date. These can later be downloaded to a computer via the anemometer’s RS232 port and the results viewed instantly on software which comes with the unit. ...
Premium
Notices Copyright CE conformity Design changes User Manual Version: 1.0 March 2002 Introduction Summary of Features Scope of This Manual Installation Unpacking Description of Equipment Component Diagram: Selecting a Site Mounting Details AN4 Sensor Connections Outline Specs Sensor Wiring Cable Data Requirements Logger Connections DL2e Logger Use with DL2e Counter ...
See Fig. 3 for connector layout:From left to right:V+ Battery positive power (red)G Battery negative power (black)G Common ground (for NTC)T NTC temperature sensorG Common ground (spare)G Common ground (wind vane)D Wind vane signalD+ Wind vane power supplyG Common ground (anemometer 2)A2 Anemometer 2 signalG Common ground (anemometer 1)A1 ...
The sensor should be located in such a way as to avoid any obstruction within at least 100 feet if possible, and up or down cur-rents, eddy currents or jet flow effects are also to be avoided.After the anemometer is fastened in place, the cable must be properly secured to the point where it will be attached to the indicator box. The indicator is then firmly ...
WL-11Innovative wind speed & direction logging systemSCARLET TECHWind Speed & Direction in One Sensor Wireless. No Running Cable Log Data on SD Card Automatically 4 Years Sensor Battery Life Instant Wind Data - Every 2 secondsScarletWind™Introduction Operating a crane in windy conditions can create a potentially dangerous situation. ...
DRAWINGS.................................................................................................................................................. 351086-M-043 Anemometer Cable (Voltage Out).............................................................................................. 36 1189-K-022 Indoor PCI Unit ...
The SIU and PCIA should be earthed using the earth studs provided. 3.5 Cabling Ensure that strain relief measures are employed when installing the cables. ...
See Section 6.4 for connection details The flying cable must be retained with a cable tie within 150mm of the base of the anemometer. ...
Anemometer Connector 20 way ? 3m Anemometer Test Cable Gill Instruments Ltd _______________________________________________________________________________________________________ Intrinsically Safe WindObserver Anemometer Page 7 Issue 07 Doc. ...
The SIU and PCI should be earthed using the earth studs provided. 3.6 Cabling Ensure that strain relief measures are employed when installing the cables. ...
The SIU and PCI should be earthed using the earth studs provided. 3.6 Cabling Ensure that strain relief measures are employed when installing the cables. ...
The flying cable must be retained with a cable tie within 150mm of the base of the anemometer. ...
The flying cable must be retained with a cable tie within 150mm of the base of the anemometer. ...
Line for symbols and comments. 17. 8-pole MiniDin connector for RS232C connection using cable HD2110CSNM and for S-print-BT printer connection using cable HD2110CSP. - - 4Thermo-Anemometer HD2103.2 - - 5HD2103.2 1. Input for probes, 8-pole DIN45326 connector. 2. ...