astm-testing Downloads
421 downloads found
Premium
Introduction These test methods cover the determination of 4-carboxybenzaldehyde (4-CBA, 4-formylbenzoic acid) and p-toluic acid (p-TOL, 4-methylbenzoic acid) in purified terephthalic acid (PTA) by capillary electrophoresis (CE) with normal or reverse voltage mode and UV ...
Premium
INTRODUCTION: This test method is applicable for determination of the dissolved inorganic anions; fluoride, bromide, chloride, nitrite, nitrate, ortho-phosphate, and sulfate in aqueous matrices using capillary ion electrophoresis with indirect UV detection. The method can be applied to drinking water, waste water and ground water. ...
Our fiberglass light rail covers are made of high-performance, high-strength, easy-to-install composites and exceed the most stringent ASTM testing requirements. For custom engineered solutions, contact an Enduro representative for assistance with material selection and ...
The Heavy-Duty Welder Harnesses are designed with rugged black Kevlar webbing to withstand harsh welding environments. They meet ASTM F887 Arc Test requirements and are rated for arc ...
The Auto-Shrink system measures the unrestrained autogenous shrinkage of a specimen of cement paste or mortar cured under sealed conditions (ASTM C1698, Test Method for Autogenous Strain of Cement Paste and Mortar). ...
WSF-1121 WSF-1010typical typicalMolded Density (pcf) 19.4-21.9 18.5-19.6 ASTM D1622Load Deflection @ 50% (psi) 60.3 29.7 ASTM D 3574, Test CCompression Set (%) 8.1 3.78 ASTM D3574, Test DSolvent Resistance Pass Pass BMS 8-350Resilience (%) 31.7 35 ASTM D3574, Test ...
11542 Davis Creek Court Jacksonville, FL 32256 800-353-1611 Website: www.stormwater- products.com E-mail: info@stormwater- products.com Ultra-BasinGuard® Specifications Minimum Average Fabric Values Properties ASTM Test Value Material: Non-woven, Polypropylene Geotextile Grab Tensile (lbs) D 4632 205 Elongation (%) D 4632 50 Trapezoid ...
Premium
The SpectrOil M/F-W has become the standard instrument when on-site and immediate fuel analysis is a necessity. It fulfills the requirements of ASTM D 6728, Standard Test Method for Determination of Contaminants in Gas Turbine and Diesel Engine Fuel by Rotating Disc Electrode Atomic Emission Spectrometry. ...
“NFP” is a water based non-toxic, non-skin irritant, non-eye irritant and biodegradable flame retardant. It has been tested under ASTM sanctioned test protocols by third party testing laboratories. Tests have been performed on all species of wood commonly used in construction, as well as other natural ...
The ABS is a microprocessor-controlled Ball-on-Cylinder wear test system which provides a fast, repeatable assessment of the performance of jet fuels that fully conforms to the ASTM D5001 test method for “Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator”. ...
The results obtained correlate to the ASTM D7483 and ASTM D445 test methods. The fast and reliable measurements allow for precise and continuous adjustment of the process, while maintaining a high correlation to laboratory quality control ...
/ft.3 (grams/cm3): 100 (1.60)ASTM F433 Thermal Conductivity (K), W/m°K (Btu.·in./hr.·ft.2·°F): 0.29-0.38 (2.00-2.65)ASTM D149 Dielectric Properties, range, volts/mil.Sample conditioning 1/16" 1/8"3 hours at 250°F: 396(3)-832 257(3)-36396 hours at 100% Relative Humidity: 271 142ASTM F586 Design Factors 1/16" & Under 1/8""m" factor: 4.2 5.2"y" factor, psi (N/mm2): ...
The quality of the product, along with the anti-abrasion and anti-scratch qualities, exceeds the performance requirements of the following microbiological resistant tests: ASTM D3273, D3274. Sporicidin Mold Resistant Coatings can be used on any new or existing building material before, during, or after installation for efficient mold proofing. ...
The two most recognized applications of the SB+2 are the Scanning Brookfield Technique (ASTM D5133 & D7110) and the Brookfield Viscosity Test (ASTM D2983). The use of the patented SimAir™ Test Cell allows the SB+2 to be held at a constant temperature during the 16-hour soak period of the Brookfield D2983 ...
MATERIAL PROPERTIES*Color: Off-whiteComposition: Aramid fibers with a SBR binderFluid Services1: Water, saturated steam4, inert gasesTemperature2, °F (°C)Minimum: -100 (-73)Continuous Max: +400 (+205)Maximum: +700 (+371)Pressure2, Maximum, psig (bar): 1200 (83)P x T (max.)2, psig x °F (bar x °C)1/32 and 1/16": 350,000 (12,000)1/8": 250,000 (8,600)Meets Specification: ABS (American Bureau of ...
Combination Octane Rating Unit/Octane test engine FTC-M is used for determining octane number of motor fuels, conforming to ASTM D2699 (ISO 5164) and ASTM D2700(ISO 5163) Standard Test Methods. ...
The double ring infiltrometer is a simple instrument used for determining water infiltration of the soil (Measurements according to ASTM D3385-03 standard test method and DIN 19682 page 7). The rings are partially inserted into the soil and filled with water, after which the speed of infiltration is measured. ...
The Thermal Integrity Profiler evaluates the concrete quality of the entire cross-section, including outside the reinforcing cage along the entire length, without maximum length limitations. TIP™ tests are completed within 48 hours of shaft casting. Although in most cases they are completed within 24 hours (earlier than any other integrity evaluation of cast-in-place ...
TRIPACFASTENERSFOR THE WATER WORKS AND CONSTRUCTION INDUSTRIESTRIPAC 2000 BLUE COATING SYSTEMBolts protected with TRIPAC 2000 BLUE COATING SYSTEM show no signs of corrosion after1,000 hours of salt spray testing (ASTM-B-117). Plain steel, zinc plated, and hot dip galvanizedbolts all show significant degrees of corrosion and rust.Tripac’s unique coating system ...