hall-sensor Downloads
87 downloads found
The JS-02 is a dual axis spring return to center full size joystick. It uses non contacting Hall effect sensors to give an expected life of more than 4 million cycles. ...
With the HPHTV the needle falling time is measured automatically by means of Hall sensors and a magnet in the needle. ...
With the UHPV-100 the needle falling time is measured automatically by means of Hall sensors and a magnet in the needle. ...
The D Series Hall Effect Speed Sensor provides enhanced machine control and system flexibility with an integrated design. ...
BEI Sensors Model 9970 Hall Effect rotary position sensor is available in two standard output configurations (0-5 V ratiometric or 4-20 mA) for ease of specification and use. Both versions use a standard Amp, Superseal three terminal connector and are available with 12 active angle ranges, 30 degrees up to 360 degrees (in 30 degree increments) in a single output device. Unlike comparable sensors ...
The SA420 interfaces with a wide variety of sensors and provides an analog signal directly proportional to the speed of a monitored shaft. ...
The MLX91209 is a fully customer-programmable monolithic sensor IC packaged in standard SIP package. The Hall current sensor IC provides a high speed analog output signal proportional to the external applied flux density. The MLX91209 current sensor enables the user to construct a precise current sensor solution with fast response time of 3µs. ...
ByMelexis
As the rotor spins the magnetic field produced by the magnets is pick up via a Hall Effect Sensor which converts the rotation into a square wave NPN pulse output that can be sent directly to a metering pump or local ...
The MLX91211 is a second-generation medium-speed current sensor that senses the magnetic field generated by the current flowing through a conductor, be it a cable, a bus bar or a PCB trace in a contactless way. ...
ByMelexis
9360Series360° Non-Contacting RotaryDual Output Hall Effect Sensor170 Technology Drive WestIrvine, CA 92618-2401(949) 341-9530 Fax: (949) 453-2700email: [email protected] BEI Sensors 9360 Series rotary sensor is a non-contacting Hall effect device with 360° of rotation and dual outputs. ...
The Texense VR-TA-G differential hall effect wheel speed sensor DHE is a class leading highly accurate and compact wheel speed sensor. ...
The MLX91207 is a fully customer programmable monolithic current sensor IC in standard SO-8 package. The Hall sensor provides a high speed analog output signal proportional to the external applied flux density and additional thermometer output. The MLX91207 current sensor enables the user to construct a robust current sensor solution with fast response times < 10usec. ...
ByMelexis
The Envoy SC is a single channel (SC) module designed for high-quality current measurements in the range from 50 to 300 Amperes. The IsoBlock Current-FG uses Hall Effect with closed loop methodology to measure the current flowing in the conductor passing through the aperture. This is followed by an anti-aliasing filter and a conditioning stage to output a ±10V signal.The compact form ...
The Texense VR-Ø9-B differential Hall effect wheel speed sensor (DHE) is a class leading highly accurate and compact wheel speed sensor. ...
This Hall Effect current sensor is based on open loop compensating principle and designed with a split core and a high galvanic isolation between primary and secondary circuits. It can be used for measurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor. ...
This IC, developed by CMOS technology, is a high-accuracy Hall effect switch IC that operates with high temperature and high-withstand voltage. The output voltage level changes when this IC detects the intensity level of magnetic flux density. Using this IC with a magnet makes it possible to detect the open / close in various devices. ...
This Hall Effect current sensor is based on open loop compensating principle and designed with a split core and a high galvanic isolation between primary and secondary circuits. It can be used for measurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor. ...
Premium
Choose your system out of a wide range of possibilities to get the best for your application. 2 Scope of delivery All Rotavapor R-250 models are delivered ready to use, including all needed tools and are complete of: Components R-250 Glass configuration according to order 1 Evaporating flask according to order 1 Vacuum hose to the vacuum source (PVC), 3.5 m 1 Vacuum hose to the vacuum ...
ByBUCHI
DKM1 is a DC gear motor with hollow shaft to drive an hex rod (not included). In addition to the compact size and low noise level, it also provides positioning feedbacks using dual Hall effect sensors to support advanced control functions. DKM1 is an economical and high quality drive solution, which possesses wide ...
The falling time is measure automatically by means of Hall sensors and a magnet in the weight holder. Like all other SBS viscometers, the CV-100 combines economy, ease of operation, accuracy, reliability, and versatility. ...