strain-sensor Downloads
76 downloads found
Strain sensors measure deflections, e.g. of steel arms, in various directions. In this way, forces, weights or vibrations can be indirectly recorded. The previously available strain sensor DMS has been revised completely and is now available in an optimized version. The newly developed hardware allows a lower height for the housing. The assembly points are identical to those of the predecessor ...
It automaticallyanalyzes the surface contour and three-dimensionaldeformation of the inspected area when a load isapplied to the component. From these data the com-plete strain field is derived within seconds.Save Time and Money with Q-100Q-100 strain measurement requires nearly no prepara-tion work and can significantly reduce the testing timefor complex ...
HOW TO INSTALL YOUR DITEST® SMARTAPES Thank you for purchasing DiTeSt® SMARTape sensors. This brochure gives you basic information on how the DiTeSt® SMARTape sensors should be installed in the most common types of applications. ...
The T100 is a Fiber Bragg Grating (FBG) Array which is available in a wide range of optical specifications. Naturally packaged directly in bare fiber, these daisy-chained FBG sensors are ultra-small and are designed for use in distributed, quasi-distributed, and multi-sensing-point applications with the added requirement of minimal intrusion. The T100 optical sensor consists 1 to 99 Fiber Bragg ...
The PHYSIMETER 906 USB measuring device is used to record mechanical variables based on strain gauge sensors. Two different versions are available: The PHYSIMETER® 906 USB with a built-in force transducer and the PHYSIMETER® 906 USB configured to connect to an external sensor. ...
FEATURES ? Distributed strain sensing ? Wide strain range ? Mechanically reinforced ? Chemically resistant ? ...
The EA250 analogue amplifier is a high-performance signal conditioner designed for strain-gauge based sensors, including load cells, force sensors, torque and pressure sensors. It converts the strain gauge input into a voltage or current output, offering a wide bandwidth and a large input signal ...
On each channel it is possible to connect up to 7 MuST deformation sensors, up to 12 MuST strain sensors (depending on sensor type, see sensor datasheets for details), or up to 25 MuST Temperature sensors. ...
Refer to the appropriate electrodespecification sheet.DIMENSIONS:PHS0 *: 0.75" dia x 13.75" lg.(1.9 cm x 34.9 cm)PHS17*: 0.75" dia x 24.00" lg.(1.9 cm x 60 cm)Dimensions are housing diameter x length of sensor.S10 sensor length is measured from front of seal guard to rearof strain relief.S17 sensor length is measured from front of the fully ...
Conax Technologies Sensor Wire Seals are designed to seal virtually any transducer, sensor or detector elements in a wide range of vacuum or pressure boundaries. The most common use of these seals is for instrument leads on vibration transducers, proximity probes, pressure sensors, temperature sensors, flow meters, and ...
ELECTRO-CHEMICAL DEVICES, INC.800-729-1333 www.ecdi.com Fax (714) 692-1222Sensor specifications REV: 4/04SPECIFICATION SUMMARYDISSOLVED OXYGEN (DO) SENSOR SPECIFICATIONModels DOS10 & DOS17MEASUREMENT RANGE:0 - 20 ppm (mg/l)0 to 200% saturationOUTPUT:Signal conditioned output, intrinsically-safe.SIGNAL CONDITIONER:Integral to sensor.T23: Model T23, T28, & T21 transmitters.C22: ...
The SEM1600/B is a “smart” powered bridge amplifier for use with strain gauges or load cell signals. The product has a built in capability to scale the input signal to a process value while the output stage offers either voltage, bipolar voltage or active / passive current re-transmission signals. The product comes with an AC/DC power supply that will operate in the range (10 to 48) V ...
BCM SENSOR linear strain gauges are specially developed for manufacturing precision force transducers which employ bending beam working principle. For the purpose of this specific application, the linear strain gauges are temperature and creep compensated, and they can be either encapsulated or open-face according to the requirement. The karma gauges can be manufactured with effective modulus ...
Sensor is used either for temperature monitoring or for thermal compensation of strain sensors. It can be glued to any monitoring steel surface. ...
The E370 DSCUSB is a compact, high performance strain gauge digital signal conditioner with USB connectivity aimed at applications which require high-accuracy measurement and repeatability. A rugged and compact ABS IP50 enclosure makes this device suitable for all environments. By simply plugging the device into a PC, data can be extracted from most strain gauge bridge input sensors and acquired ...
The Spider-80SG is a high precision, general purpose data acquisition device featuring strain gage measurement. This device can be used in a variety of physical and measurement tests. The Spider-80SG can acquire data from a strain gage or a wide range of measurement quantities. A variety of general purpose and strain gage based sensors are supported. The Spider-80SG is built on the proven ...