thrust-boring Downloads
16 downloads found
The PD-6 can install pipes by either directional thrust boring or pipe bursting. These machines are excellent in areas where space is limited. The PD-6 will operate from a pit only 56 inches long and has a thrust force of 84,822 lbs@ 3,000 psi. The maximum push rate of PD-6 is 7 feet/minute and it can install up to 8-inch ID pipe in most ...
Thrust: 600,000 lbs. (272 tonnes)Hydraulic Thrust Cylinder: (2) 9 in. bore x 35 in. stroke (229 mm x 889 mm)Max. Thrust: 900,000 lbs. (408 tonnes)Hydraulic Thrust Cylinder: (3) 9 in. bore x 35 in. stroke (229 mm x 889 mm)Max. Thrust: 1,200,000 lbs. (544 ...
Unequalled Mobility (5 degrees of freedom) ? Equal Forward and Lateral Thrust for equal speed in all directions To make the most of the AC-ROV’s manoeuvrability, the system uses a truly intuitive 3D controller with a single handed grip that can be moved in any direction, rotated and tilted. ...
ANDRITZ High-Pressure PumpMP SeriesPump size Delivery branchDNd [mm]Inlet branchDNs [mm]HydraulicsystemFlow rate50 Hz Q [m3/h]60 HzMP 40 40-65-40.240.330423650MP 65 65-100-65.165.2709080110MP 100 100-125-100.1100.2150200180240MP 125 125-150 -125.1125.2240300280360MPE 65 65-100-65.165.250756090 MPE 100 100-125-100.1100.2110145132175MPE 125 125--150--125.0125.1125.2200260350240312420Modular ...
•Self-lubricating bushings for continuous low-friction operation.•Two-way, field-adjustable thrust bearing permits flexibility in valve and actuator orientation.The Streamseal™Butterfly ValveDesign FeaturesMeets established requirements of AWWA Standard C504.1. ...
.• Compact designSizes• NMB 32–125 to NMB 80–200Technical design• Axial suction socket and radial pressure socket• Closed radial impeller• Axial thrust compensation by relief bores• Impeller mounting independent of the rotational di-rection• Corrosion protection by a 2C paint coatDrive• Three-phase motor up to 7,5 kW acc. to IEC• Motor with extended stainless ...
DTD specializes in environmental applica-tions of guided boring technology, including the installation of remediation wells and venting systems, groundwater resource de-velopment, and subsurface sampling. ...
Hg (660.4 torr) (wet) to remove excavated material from the bore. VACUUM TANK Upon reaching the launch pit, the excavated material transitions from the drill casing to a 6-inch (15.2 cm) diameter hose running up the launch pit to a 2000 gal (7570.8 L) or 800 gal (3028.3 L) vacuum tank.RACK POWER UNIT A self-contained rack power unit features a 140-hp (104.4 kW) diesel engine and ...
ByVermeer
.: 340021 – 2012/01/02Design• Horizontal, single-stage, non self-priming chemicalpump according to DIN 24256, EN 22858, ISO 2858with single flow spiral casing of modular conceptSizes• NM 32–125 to NM 150–400Technical design• Axial suction socket and radial pressure socket• Closed radial impeller• Axial thrust compensation by relief bores• Impeller mounting ...
.: 340021 – 2012/01/02Design• Horizontal, single-stage, non self-priming chemicalpump according to DIN 24256, EN 22858, ISO 2858with single flow spiral casing of modular conceptSizes• NM 32–125 to NM 150–400Technical design• Axial suction socket and radial pressure socket• Closed radial impeller• Axial thrust compensation by relief bores• Impeller mounting ...
Put front thrust washer into new shaft support.3. Position the front shaft support in the bore of the casing suction and align the anti-rotation pins on the front shaft support with the blind holes in the casing. 4. ...
Special variants include part-turn actuators for 90° or 120° angles of rotation and thrust actuators, which transform the torque into an axial thrust by means of a thrust unit. ...
Special variants include part-turn actuators and thrust actuators, which transform the torque into an axial thrust by means of a thrust unit. ...
Design:Horizontal, high pressure, multi-stage centrifugal pump in robust, heavyduty design for continuous operation. Balancing of axial thrust is done byrelease borings (for higher pressure with relieving piston and also opposi-tely directed). ...
The thrust actuator transforms the torque of a DREHMO® actuator into an axial thrust by means of an integrated thrust unit.The required actuating force (thrust or traction) can be adjusted continuously and reproducibly. ...
Special variants include part-turn actuators and thrust actuators, which transform the torque into an axial thrust by means of a thrust unit. ...