Refine by
Flap Damper Equipment & Supplies
19 equipment items found
Manufactured by:Yrjas Dampers AB based inNYLAND, SWEDEN
Dampers for mainly on-off operating of flue gases in an industrial ...
Manufactured by:Fox Equipment, LLC based inGreen Cove Springs, FLORIDA (USA)
Diverters /Flap Dampers are primarily used in gas turbine applications with heat recovery steam generators (HRSG). A diverter damper is designed with one inlet and two outlets. The outlets are normally at right angles from each other. The blade pivots from one end rotating 90 degrees to close off one of the two outlets. ...
Manufactured by:V-Tork Controls based inCoimbatore, INDIA
Butterfly dampers are used for isolation or control application .These dampers are lightweight, wafer , round port, quickly actuated and cost wise economical .These dampers are single louver or double louver(flap)in design. Damper flaps are thin since, angle or bars will stiffen the ...
Manufactured by:MedicCleanAir, Division of Walsberghe nv based inAntwerp, BELGIUM
(immune-compromised patients). Both parts are connected by a tube – through the wall – which contains an air back-pressure flap (standard) and fire damper (optional). Filters used in this Isolation Unit are of HEPA14 or ULPA15 quality, leaktested and airtight ...
Manufactured by:Jasta Armaturen GmbH & Co.KG based inEssen, GERMANY
The rectangular control damper is our solution for rectangular flange connections. We also offer them in the multi-leaf ...
Manufactured by:Barat Industrial Plastic Engineering Co. based inKartepe, TURKEY
Air damper manufacturing, manufacturing clapper, clapper plastic manufacturing, plastics manufacturing damper industrial ventilation lines, to regulate the air flow, increase the air speed - reducing, pressure regulation is designed to do. In particular, acid vapor, chemical (corrosive) will wear the mechanical valve mechanism for transporting the air duct of steam, rust and so on. due to defects ...
Manufactured by:Arslan Damper Makina San. ve Tic A.Ş. based inAliaga, TURKEY
Tipper body fixed cover: Floor thickness: 8 mm HARDOX 450. Side walls thickness: 6mm ST 52 steel sheet. Front Wall thickness: 6 mm ST 52 steel sheet. Tailgate thickness: 6 mm ST 52 steel sheet. Reinforcements: 4 mm ST 52 steel sheet. The operating system of the tailgate is manual. Opening both on rear and ...
Manufactured by:Redi Haul Trailers based inFairmont, MINNESOTA (USA)
Main Frame: 10' x 15# I-Beam, high strength structural steel. Frame Bedside: 8' x 11.5# Channel, high strength structural steel.Bed Crossmembers: 5' x 6.7# Channel, high strength structural steel pierced through tilt bed stringer (8' x 13# I-Beam, high strength structural ...
Manufactured by:Arslan Damper Makina San. ve Tic A.Ş. based inAliaga, TURKEY
This type of tipper is suitable for the transportation of the light excavation material and pallets. The dimensions of the tipper body depends on the vehicle chassis measurements. For different applications, please fill the request form. The recommended volumes for the 6x4 chassis vehicles are 14 m3, 16 m3, 18 m3 and 20 m3. The recommended volumes for the 8x4 chassis vehicles are 20 m3, 22 m3, 24 ...
Manufactured by:Arslan Damper Makina San. ve Tic A.Ş. based inAliaga, TURKEY
This type of tipper is suitable for the transportation of the light excavation material and pallets. The dimensions of the tipper body depends on the vehicle chassis measurements. For different applications, please fill the request form. The recommended volumes for the 6x4 chassis vehicles are 14 m3, 16 m3, 18 m3 and 20 m3. The recommended volumes for the 8x4 chassis vehicles are 20 m3, 22 m3, 24 ...
Manufactured by:Arslan Damper Makina San. ve Tic A.Ş. based inAliaga, TURKEY
This type of tipper trailer is suitable for the transportation of the light excavation material and ...
Manufactured by:Arslan Damper Makina San. ve Tic A.Ş. based inAliaga, TURKEY
Tipper body: Body: Hardox 450 (SSAB). Floor thickness: 5 mm HARDOX 450. Side walls thickness: 4 mm HARDOX 450. Tailgate thickness: 4 mm HARDOX 450. Front Wall thickness: 4 mm HARDOX 450. The operating system of the tailgate is manual. Opening both on rear and ...
Manufactured by:Arslan Damper Makina San. ve Tic A.Ş. based inAliaga, TURKEY
Hook - lift: Capacity: 25 tonnes loading unloading. Unloading angle: 45-50 ...
Manufactured by:Process Barron based inPelham, ALABAMA (USA)
ProcessBarron's Flow Diverter Dampers are essential for efficient heat recovery systems, directing gas flow to either a waste heat recovery system or a bypass mode through a silencer or stack. Engineered with a single end pivoted blade, these dampers ensure precise control of gas flow between two damper outlets. Our turbine exhaust diverter dampers come fully equipped with two dampers, T-duct ...
Manufactured by:Arslan Damper Makina San. ve Tic A.Ş. based inAliaga, TURKEY
Hook – lift (8x2 truck). Capacity: 25 tonnes loading unloading. Unloading angle: 45-50 degrees. Sub-frame: 10 mm. ...
Manufactured by:Colchester Engineering Systems (CES) based inColchester, UNITED KINGDOM
This type is simply used for fitting in to a duct system where it is necessary to close-off the airway when the ventilation plant has stopped, or for use where a fire protection system requires a sealed space into which a fire suppressant gas can be discharged without major loss. The standard type is not gas tight. We can supply a low leakage version that includes blade seals and side gap shim ...
Manufactured by:Miteck Systems based inMumbai, INDIA
Butterfly dampers are typically used to intercept or regulate gas flows; they are similar to single-louver dampers with one blade and they can be used in round or square/rectangular ducts. Blade is typically designed with air-foil configuration which minimizes the pressure drop; shafts are made of solid section and “stub” type to be connected to the blade by keys and blocks. This ...
Manufactured by:Mitsubishi Hitachi Power Systems, Ltd. (MHPS) based inLake Mary, FLORIDA (USA)
Mitsubishi Hitachi Power Systems has a license agreement with Balcke-Dürr GmbH, a subsidiary of SPX Corporation, to design and supply fabric filters for the US market. Hitachi and Balcke-Dürr have been working together for many years in the European market . With a proven track record in dust collection technologies and over 100 fabric filter installations worldwide, our innovative ...
Manufactured by:BIOGEST AG based inTaunusstein, GERMANY
The BIOGEST Gate Flushing System Type KS is engineered to address the challenges faced with sediment build-up in storm tanks and sewers post-storm operations. This system is crucial in mitigating risks like blockages and odors that arise due to sediment accumulation and septicity. Constructed from robust stainless steel options such as AISI 304 and AISI 316Ti, it comprises essential components ...