Refine by
Geosoft Xprt Software In Spain
10 software items found
by:Geosoft International based inTurin, ITALY
The program classifies rock masses using both the Bieniawski and the Barton methods, making it thus possible to compare the results that can be obtained with the two most frequently used classification methods. The Bieniawski classification (RMR Index) evaluates different parameters to which a numerical coefficient is assigned. The sum of these coefficients determine the Rock Mass Rating class ...
by:Geosoft International based inTurin, ITALY
This program perform all the function of the Isomap package and can be considered as it extension. Most of the complex problems related to ground-water modeling can be solved with INQUIMAP. It allows the geometric modeling of the water table and the insertion of one or several wells, flooded areas, barriers and impermeable barriers, recharge points and variations in permeability. The obtained ...
by:Geosoft International based inTurin, ITALY
ROTOMAP is a three-dimensional model that is used for rockfall analysis and the design of rockfall protective systems. This module belongs to the Isomap family: please check the ISOMAP page for a complete description of the main module features. ROTOMAP uses a statistical approach; it simulates a large number of rockfalls and, through the analysis of the distribution of the average and maximum ...
by:Geosoft International based inTurin, ITALY
ISOMAP is the module that is used to calculate and render surfaces through contour lines or coloured and shaded areas with a high degree of precision. The program allows the representation of the surface both in topographic map and perspective view forms. The calculation is performed in two stages. The first stage consists of creating a regular grid from a collection of arbitrarily positioned ...
by:Geosoft International based inTurin, ITALY
ELETOM is a software that performs complete 2D inversion (and not the simple iterative deconvolution of the pseudo-sections) of surface electrical surveys with any measurement array (Wenner, dipole-dipole, pole-dipole, pole-pole, user defined arrays, mixed arrays) with a maximum of 64 electrode positions that can be added by the user as required. ELETOM uses the finite elements method (FEM) in ...
by:Geosoft International based inTurin, ITALY
ROCK3D is a program for stability analysis of removable blocks on planar rock slopes. It identifies and analyses all the blocks that have formed under each kinematic mode. Once the geometry of the rock blocks has been identified, the bolt forces necessary to reach a required safety factor are calculated. The structural geology data collection is carried out through the introduction of the joint ...
by:Geosoft International based inTurin, ITALY
CLU-STAR is a program for computerised structural geology data collection and analysis. The program recognises the discontinuity sets of a rock mass through hierarchical and non-hierarchical clustering procedures derived from the multivariate analysis. These clustering procedures operate directly on the collected data instead of on their statistical distribution; the results are consequently ...
by:Geosoft International based inTurin, ITALY
Ce.Ca.P. is a complete package for the analysis and design of foundations; because of its completeness, flexibility ad user-friendliness it is a fundamental instrument for any kind of geotechnical project. To calculate the bearing capacity of foundations, the following methods can be used: Terzaghi, Meyerhof, Hansen and Vesic. Such methods are based on different hypotheses regarding failure ...
by:Geosoft International based inTurin, ITALY
The program analyses the behaviour of the rock slopes under seismic conditions. It evaluates the displacements of a rock block subject to dynamic forces, on the basis of a given accelerogram. The use of a calculation method based on a given accelerogram for rock slope stability analysis allows one to take into account the duration and the intensity of the accelerogram itself (this not being the ...
by:Geosoft International based inTurin, ITALY
I.L.A. is a complete slope stability analysis program that also incorporates powerful features for retaining system designing. The slope analysis and design can be performed using the Sarma method, whose numerical stability increases the reliability of the calculations. The classic Bishop, Jambu, Morgenstern & Price and Bell methods are also available; this allows to compare the results and ...