astm-testing-method Downloads
149 downloads found
Premium
Introduction These test methods cover the determination of 4-carboxybenzaldehyde (4-CBA, 4-formylbenzoic acid) and p-toluic acid (p-TOL, 4-methylbenzoic acid) in purified terephthalic acid (PTA) by capillary electrophoresis (CE) with normal or reverse voltage mode and UV ...
Premium
INTRODUCTION: This test method is applicable for determination of the dissolved inorganic anions; fluoride, bromide, chloride, nitrite, nitrate, ortho-phosphate, and sulfate in aqueous matrices using capillary ion electrophoresis with indirect UV detection. The method can be applied to drinking water, waste water and ground water. ...
The Auto-Shrink system measures the unrestrained autogenous shrinkage of a specimen of cement paste or mortar cured under sealed conditions (ASTM C1698, Test Method for Autogenous Strain of Cement Paste and Mortar). ...
The results obtained correlate to the ASTM D7483 and ASTM D445 test methods. The fast and reliable measurements allow for precise and continuous adjustment of the process, while maintaining a high correlation to laboratory quality control ...
Premium
The SpectrOil M/F-W has become the standard instrument when on-site and immediate fuel analysis is a necessity. It fulfills the requirements of ASTM D 6728, Standard Test Method for Determination of Contaminants in Gas Turbine and Diesel Engine Fuel by Rotating Disc Electrode Atomic Emission Spectrometry. ...
The double ring infiltrometer is a simple instrument used for determining water infiltration of the soil (Measurements according to ASTM D3385-03 standard test method and DIN 19682 page 7). The rings are partially inserted into the soil and filled with water, after which the speed of infiltration is measured. ...
Combination Octane Rating Unit/Octane test engine FTC-M is used for determining octane number of motor fuels, conforming to ASTM D2699 (ISO 5164) and ASTM D2700(ISO 5163) Standard Test Methods. ...
The Thermal Integrity Profiler evaluates the concrete quality of the entire cross-section, including outside the reinforcing cage along the entire length, without maximum length limitations. TIP™ tests are completed within 48 hours of shaft casting. Although in most cases they are completed within 24 hours (earlier than any other integrity evaluation of cast-in-place ...
The ASTM D3273 test chamber contains soil that was seeded with fungal spores and allowed to grow. The test samples were hung in the D3273 chamber with three pieces of the positive growth control to confirm validity of the fungal inoculum coming from the soil. Samples were examined weekly for fungal growth and defacement and rated according to visual defacement of fungal ...
For applications where potable water is available, CalgonCalgon Carbon Corporation recommends using Centaur® HSV, anactivated carbon with the highest H2S capacity in the industry,achieved through its water regenerability.The determination of H2S capacity will be made through the use of ASTM Test Method D-6646.Pressure Drop in a Deep Bed Odor ...
Fully rubber lined waterway with integral rubber seat vulcanized to body and tested to ASTM D429 Method B4. Streamlined epoxy coated ductile iron disc with 316 stainless steel seat edge 5. ...
Box 640 Willacoochee, GA 31650 Phone: 800-948-7870 Fax: 912-534-6254 Lightweight Orange Plastic Barrier Fence This letter certifies that our Orange Plastic Barrier Fence meets the requirements for Plastic Barrier Fence that meets AL DOT. The average laboratory test values are as follows: Material Polypropylene Roll size 4' x100' (width x length) Color Orange ...
D. ASTM D-695: Test Methods for Compressive Properties of Rigid Plastics. E. ASTM D-2584: Test Method for Ignition Loss of Cured Reinforced Resins. ...
Animal Shelter Noise AttenuationTechnical Data APPLICABLE STANDARDS ? ASTM C423 Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method ? ASTM E84 Standard Test Method for Surface Burning Characteristic of Building Materials? ...
Premium
.)• KOGAS• ENI• PETROBRAS• Beijing Gas Company• Shanghai gas (Chine)• ALSTOM• DEGREMONT• VEOLIA• THALES• Europe air monitoring stations Germany / France /Benelux / United Kingdom / Spain / Italy / Austria /Croatia / Slovenia / Hungary / Poland / Slovakia / Bosnia / Czech Republic / Serbia• Africa : South Africa /Benin• Asia : meteorology & ambient air networks TEPA (Taiwan / ...
D. ASTM D 570 – Standard Test Method for Water Adsorption of Plastics. E. ...
D. ASTM D-695: Test Methods for Compressive Properties of Rigid Plastics. E. ASTM D-2584: Test Method for Ignition Loss of Cured Reinforced Resins. ...
ASTM D-695: Test Methods for Compressive Properties of Rigid Plastics.E. ASTM D-2584: Test Method for Ignition Loss of Cured Reinforced Resins.F. ...
Tel: 800-626-2180 603-673-8680 Fax: 603-673-7271 www.trelleborg.com/npc Kor-N-Seal® Product Line Technical Specifications PERFORMANCE Performed on all standard sizes of Kor-N-Seal Connectors. Test ASTM Method Test Requirements Kor-N-Seal Products Head Pressure C923 - 7.1 0° - 13 psi (30 ft) for 10 min. +13 psi ...
Combination (RON and MON method) Octane Rating Unit SINPAR FTC-M provides a complete system for octane determination, conforming to ASTM D2699 (RON) and ASTM D2700 (MON) Standard Test Method. CFR Octane engines provide the capability to switch between Research and Motor Methods. The testing capabilities cover the 40 -120 octane number range. For more details about CFR octane rating unit, please ...